Siemens SIMOTION P320-3 Скачать руководство пользователя страница 77

Страница: 77 / 150

Installing/Mounting

5.1 Installing SIMOTION P320-3

SIMOTION P320-3 and Panel Fronts
Manual, 02/2012

NOTICE

The rails are secured to a wall or cabinet similar to mounting with mounting brackets.

Ensure that the wall or ceiling can hold four times the total weight of the device (including

the rails and additional expansion modules). See also section Mounting with mounting

brackets (Page 77).

Removing the device from the mounting rails

● Push the device down until the clamps release it.
● Swing the device away from the rails.

5.1.3

Mounting with mounting brackets

Removing mounting clamps from the device

Two mounting clamps are factory installed on the device for mounting onto standard rail.

These need to be removed before mounting the mounting brackets.

Steps for removing the mounting clamps
Remove the four screws

②

and

the two mounting clamps

①

from

the back of the device.

Содержание SIMOTION P320-3























































































































































Результаты поиска

Содержание SIMOTION P320-3

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMOTION P320-3, Руководство пользователя

Результаты поиска

Содержание SIMOTION P320-3

Отзывы:

Бренды по названию

Популярные бренды