Siemens SIMOTION P320-3 Скачать руководство пользователя страница 75

Страница: 75 / 150

SIMOTION P320-3 and Panel Fronts
Manual, 02/2012

Installing/Mounting

5.1

Installing SIMOTION P320-3

5.1.1

Mounting information

Requirement

Before you install the device, read the following mounting instructions.

NOTICE

Adhere to the relevant DIN/VDE requirements or the country-specific regulations when

installing in control cabinets.

NOTICE

Ensure that the device is classified as "Open Type" when using it in the area of Industrial

Control Equipment (UL508). A UL508 conform enclosure is therefore a mandatory

requirement for approval or operation according to UL508.

Types of installation

The following SIMOTION P320-3 installation types are permitted and described in the

following sections:
●  Mounting onto standard rail (Page 76)
●  Mounting with mounting brackets (Page 77)
●  Book mounting (Page 79)

Содержание SIMOTION P320-3























































































































































Результаты поиска

Содержание SIMOTION P320-3

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMOTION P320-3, Руководство пользователя

Результаты поиска

Содержание SIMOTION P320-3

Отзывы:

Бренды по названию

Популярные бренды