Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 41

Страница: 41 / 188

4.6

Thermal motor protection

The machine is equipped with measuring equipment for direct monitoring of the motor

temperature to protect the machine against overload during operation. Plan a corresponding

circuit for monitoring.

4.7

Thermal motor protection using PTC thermistors (option)

The machine is equipped with PTC thermistors for direct monitoring of the motor temperature

to protect the machine against overheating during operation. Plan a corresponding circuit for

monitoring.

4.8

Interlock circuit for the automatic regreasing system (option)

Relubrication is permitted only for a rotating shaft. Consequently, deploy an interlock circuit

for machines with automatic regreasing system to prevent them from operating at machine

standstill.

4.9

Interlock circuit for anti-condensation heating

If the anti-condensation heating is operated while the machine is running, this can increase

the temperatures inside the machine.
● Install an interlock circuit that switches off the anti-condensation heating once the main

machine is switched on.

● Only switch on the anti-condensation heating after the machine has been switched off.

Содержание SIMOTICS FD 1LL1





























































































































































































Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды

Siemens SIMOTICS FD 1LL1, Инструкция по эксплуатации и установке

Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды