Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 188

background image

WARNING

Live parts
Electric machines contain live parts.
Fatal or severe injuries and substantial material damage can occur if the covers are removed

or if the machine is not handled, operated, or maintained properly.
● Always observe the “five safety rules" (Page 16) when carrying out any work on the

machine.

● Only remove the covers using the methods described by these operating instructions.
● Operate the machine properly.
● Regularly and professionally maintain the machine according to the instructions provided

in Chapter "Maintenance".

WARNING

Rotating parts
Electric machines contain dangerous rotating parts.
Fatal or severe injuries and substantial material damage can occur if the covers are removed

or if the machine is not handled, operated, or maintained properly.
● Only remove the covers using the methods described by these operating instructions.
● Operate the machine properly.
● Regularly and correctly maintain the machine.
● Secure free shaft extensions and other rotating part such as couplings and pulley belts

so that they cannot be touched.

WARNING

Hot surfaces
Electric machines have hot surfaces. Touching hot surfaces can result in severe burns.
● Allow the machine to cool before starting work on the machine.
● Only remove the covers using the methods described by these operating instructions.
● Operate the machine properly.

CAUTION

Hazardous substances
Chemical substances required for the setup, operation and maintenance of machines can

present a health risk.
Poisoning, skin damage, cauterization of the respiratory tract, and other health damage may

result.
● Read the information in these operating instructions and the product information supplied

by the manufacturer.

● Observe the relevant safety regulations and wear the personal protective equipment

specified.

Safety information

2.4 Safe handling

SIMOTICS FD 1MH1

Operating Instructions 08/2017

17

«
...
15
16
17
18
19
...
»

Содержание SIMOTICS FD 1LL1





























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMOTICS FD 1LL1

Бренд: YOODA Страницы: 6

Бренд: Iveco Motors Страницы: 6

Бренд: Westerbeke Страницы: 86

Бренд: Daytona Страницы: 18

Бренд: ebm-papst Страницы: 9

Бренд: Mercedes-Benz Страницы: 940

PneuTorque PTS-52-500

Бренд: norbar Страницы: 30

Бренд: Farymann Diesel Страницы: 76

Бренд: RHINO Страницы: 20

Бренд: Vanguard Страницы: 124

Бренд: fadini Страницы: 56

Бренд: Brother Страницы: 76

Бренд: Brother Страницы: 112

Бренд: Brother Страницы: 22

Бренд: Saito Страницы: 2

Бренд: Saito Страницы: 2

Бренд: Saito Страницы: 7

Бренд: Habasit Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды