Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 188

background image

Converter operation
● If the design of the motor requires connection to a particular converter type, the rating plate

will contain corresponding additional information.

● The converter is correctly parameterized. The parameterization data is specified on the

rating plate of the machine. Information about the parameters is available in the operating

instructions for the converter.

● Any supplementary motor monitoring devices and equipment have been correctly

connected and are functioning correctly.

● In continuous operation, the motor cannot exceed the specified upper speed limit n

max

or

undershoot the lower speed limit n

min

.

The permissible acceleration time to the limit speed n

min

depends on the parameter

assignment.

WARNING

Dangerous voltage via the converter
As long as the feeding converter is switched on, or the DC link of the converter is not

discharged, there can be a voltage at the motor terminals even when the rotor is not moving.

The voltage is up to 1000 V, depending on the converter type.
Ensure that the five safety rules (Page 16) are followed before working on the motor.

7.3

Measuring the insulation resistance before commissioning

Measuring the insulation resistance and polarization index (PI) provides information on the

condition of the machine. It is therefore important to check the insulation resistance and the

polarization index at the following times:
● Before starting up a machine for the first time
● After an extended period in storage or downtime
● Within the scope of maintenance work
The following information is provided regarding the state of the winding insulation:
● Is the winding head insulation conductively contaminated?
● Has the winding insulation absorbed moisture?
As such, you can determine whether the machine needs commissioning or any necessary

measures such as cleaning and/or drying the winding:
● Can the machine be put into operation?
● Must the windings be cleaned or dried?
Detailed information on testing and the limit values can be found here:
"Testing the insulation resistance and polarization index" (Page 61)

Start-up

7.3 Measuring the insulation resistance before commissioning

SIMOTICS FD 1MH1

Operating Instructions 08/2017

107

«
...
105
106
107
108
109
...
»

Содержание SIMOTICS FD 1LL1





























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMOTICS FD 1LL1

Бренд: Mitsubishi Страницы: 176

Бренд: Habasit Страницы: 54

Бренд: TOPMAQ Страницы: 17

Бренд: Nissei Страницы: 16

Compact CA Series

Бренд: Hägglunds Страницы: 45

Бренд: Ebmpapst Страницы: 18

Бренд: ebm-papst Страницы: 11

Бренд: Sachs Страницы: 52

Бренд: MW Fly Страницы: 93

Бренд: Albin Страницы: 31

Бренд: FIAMA Страницы: 7

Бренд: Yanmar Страницы: 280

Бренд: Honda Страницы: 182

Бренд: PYD Electrobombas Страницы: 36

Бренд: O.S. engine Страницы: 20

MAX-12CV Series

Бренд: O.S. engine Страницы: 30

Бренд: O.S. engine Страницы: 38

Бренд: HELIX Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды