Siemens SIMOCODE 3UF Скачать руководство пользователя страница 142

Страница: 142 / 172

Online Settings and Displays

17.2 Command

SIMOCODE PRO V PN FDI

142

Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

17.1.3

Error Buffer - Error Protocol - Events DM-F

When using a DM-F, the events "Enabling circuit closed" and "Enabling circuit open" are

logged for the "DM-F Local" and/or the "DM-F PROFIsafe" in a separate window:

●

Time

●

Event: "Enabling circuit closed" or "Enabling circuit open"

●

Text:
–

Line 1: "DM-

F Local enabling circuit 0 → 1" or "DM

F PROFIsafe enabling circuit 0 → 1"

–

Line 2: "DM-

F Local enabling circuit 1 → 0" or "DM

F PROFIsafe enabling circuit 1 →

0".

17.2

Command

In dialogue "Command" the following commands can be sent to SIMOCODE pro:

Note
Commands are immediately carried out!

Command

Meaning

Program memory module

Transfer of the parameters into the memory module.

The memory module must be plugged into the system

interface.

Erase memory module

Parameters in the memory module are deleted. The

memory module must be plugged into the system

interface.

Read memory module

Transfer of the parameters from the memory module to

the basic unit. The memory module must be plugged

into the system interface.

Содержание SIMOCODE 3UF













































































































































































Результаты поиска

Содержание SIMOCODE 3UF

Отзывы:

Похожие инструкции для SIMOCODE 3UF

Бренды по названию

Популярные бренды

Siemens SIMOCODE 3UF, Руководство по программированию и эксплуатации

Результаты поиска

Содержание SIMOCODE 3UF

Отзывы:

Похожие инструкции для SIMOCODE 3UF

Бренды по названию

Популярные бренды