English
Important
This quick start manual is only intended for use by professional installers who have
an adequate working knowledge of video systems!
This manual outlines the most important information about the SIMATRIX NEO
Alarm box. It is, however, vital that you also refer to the detailed information in the
full operating instruction of SIMATRIX NEO.
Installation and set-up
Step 1: Provisionally connect the SIMATRIX NEO to the electrical supply
Required power supply: TN network (to VDE 0100, section 300 or EN 60950)
Voltage range: 110 - 240 Volt
Once the system has been connected to the electrical supply, and assuming the
device is in good operating the LED at the front of the unit will lit.
To continue installation, you must now unplug all NEO components at the mains!
Step 2: establish SysLink-connection
Use the marked
SysLink-cable
to connect the
SysLink-input
of Alarm box
(SIMNEO-A128) to the
SysLink-output
of SIMATRIX NEO main or extension bay.
In case a second alarm box has to be installed, connect
SysLink-input
to
SysLink
output
of first alarm box.
Step 3: setup device adress
First alarm box must be set to device address „2“, the second alarm box must be set
to address „3“.
Step 4: set config-switch
In case the alarm box is the last device on SysLink-Bus, the switch
R
must be set
to
On
, all other terminations must be switched
Off
. In case the device is not at the
end of the SysLink-Bus, all switches must be set to
Off
.
Step 5: change alarm base parameters
Control software: Alarm base parameters button
Alarm sensor settings
Step 6: Alarm sensor to camera allocation
Control software: Sensors / Camera groups button
Step 7: Further programming
If applicable, enter further parameters in order to tailor the function of the SIMATRIX
NEO to suit individual operating needs and the rest of the system.
Step 8: Make a back-up of the parameter settings and store the back-up close
to the system.
Operation and storage
Do not operate or store the unit in following locations:
•
Extremely hot or cold places
•
Close to sources of strong magnetism
•
Close to sources of powerful electromagnetic radiation such as radios or TV
transmitters.
•
In humid or excessively dusty places
•
Where exposed to mechanical vibrations.
Care and maintenance
The alarm box is maintenance-free.
Use a clean soft piece of cloth to wipe small amounts of dirt or dust from the body.
Specifications
Alarm Inputs:
128 Alarm Inputs, (4 x 32 Inputs)
Input resistance:
2,2 Kilo Ohm
Threshold:
2,5 V DC
Max. voltage:
internal pull-up (max. 24 V DC external)
Alarm pulse:
min. 300 milliseconds
Length Alarm-cable:
max. 10 m
Connection Alarm:
4 x 37-pin Sub-D
Controller
1 RISC-Controller
Interface
SysLink
Power requirement
115 / 230 VAC (+10% / -15%), 50/60 Hz
(internal switchable)
Fuse
2 x 125 mA slow
Power consumption
3 VA
Operating temperature
+ 5
°
C to 45
°
C
Relative humidity
30 to 85 %, non condensing
Construction:
19 inch chassis
, 1 HU
Dimensions (W x H x D): 449 x 44 x 206 mm (without 19” mount)
D
a
ta
a
n
d
d
e
s
ig
n
s
u
b
je
c
t
to
c
h
a
n
g
e
w
it
h
o
u
t
n
o
ti
c
e
©
2
0
0
5
S
ie
m
e
n
s
B
u
ild
in
g
T
e
c
h
n
o
lo
g
ie
s
:
F
ir
e
a
n
d
S
e
c
u
ri
ty
P
ro
d
u
c
ts
