Siemens SIMATIC S7-1200 CP 1243-8 IRC страница 108 Скачать руководство пользователя | Manualshive

Страница: 108 / 230

background image

Configuration

4.16 Security

CP 1243-8 IRC

108

Operating Instructions, 02/2018, C79000-G8976-C385-03

●

Key exchange interval
Period after which the key is exchanged again between the CP and the master. The

interval must be matched up on both communications partners.
Range of values: 0...65535 min. at 0 (zero), the key is never changed (function disabled).

Default setting: 15 min.
Recommendation: Set the key exchange interval for the CP twice as high as for the

master.

●

Authentication timeout
Maximum waiting time for the response from the master to an authentication request of

the CP.
Exceeding the wait time is evaluated as an error by the CP. In this case, the CP

generates a security event and sends this to the master.
Range of values: 1... 65535 s Default setting: 5

●

Pre-shared key
The pre-shared key can be configured in two ways:
–

Manual configuration
Enter the pre-shared key in STEP 7 manually as a hexadecimal value.

–

Import as file
Import the pre-shared key from the file system of the engineering station if the pre-

shared key was generated by the master or another system.

The pre-shared key of the CP must be identical to the pre-shared key of the master.

4.16.4

Firewall

4.16.4.1

Pre-check of messages by the MAC firewall.

Each incoming or outgoing frame initially runs through the MAC firewall (layer 2). If the frame

is discarded at this level, it will not be checked by the IP firewall (layer 3). This means that

with suitable MAC firewall rules, IP communication can be restricted or blocked.

4.16.4.2

Firewall settings for configured connection connections via a VPN tunnel

IP rules in advanced firewall mode

If you set up configured connection connections with a VPN tunnel between the CP and a

communications partner, you will need to adapt the local firewall settings of the CP:
In advanced firewall mode ("Security > Firewall > IP rules") select the action "Allow*" for both

communications directions of the VPN tunnel.
See section Settings for online security diagnostics and downloading to station with the

firewall activated (Page 109) for information on this.

«
...
106
107
108
109
110
...
»

Содержание SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC S7-1200 CP 1243-8 IRC

Бренд: 3xLogic Страницы: 2

Бренд: F5 Страницы: 2

Бренд: F5 Страницы: 90

Бренд: F5 Страницы: 47

8677 - BladeCenter Rack-mountable - Power...

Бренд: IBM Страницы: 126

Бренд: SIIG Страницы: 20

Бренд: ekwb Страницы: 11

Бренд: Dataprobe Страницы: 16

Бренд: ZALMAN Страницы: 18

Бренд: Corsair Страницы: 12

Бренд: Intellinet Страницы: 2

ARC-12x4 Series

Бренд: Areca Страницы: 2

Бренд: Dave Embedded Systems Страницы: 79

Бренд: CyberResearch Страницы: 59

ExtremeCloud Appliance E3120

Бренд: Extreme Networks Страницы: 27

Бренд: AMD Страницы: 10

Ultra Wireless AWN-8030

Бренд: Adaptec Страницы: 57

GigaVUE H Series

Бренд: Gigamon Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды