Siemens SIMATIC RF1000 Series Скачать руководство пользователя страница 40

Страница: 40 / 77

Programming

6.2 Programming via USB/RS232 interface (using DLL functions)

SIMATIC RF1000

Operating Instructions, 02/2020, C79000-G8976-C432-07

Parameter

Description

Status

•

ERR_NOMESSAGE

•

ERR_AR_DISABLED

You will find more information on the reader status in the section "Status

codes (Page 55)".

resp

Buffer for the received data

•

Byte 0: Message type (0x00 for card identification)

•

Byte 1: Message length in bytes

•

Byte 2: ... message 1: Message data

resp_len

Current length of the response data in bytes

max_resp_len

Maximum length of the response data

Return value

•

BRP_OK

You will find more information on return values in the section "Return val-

ues (Page 40)".

6.2.1.17

Return values

The following table contains a list of the possible values that the reader can return for the

various functions.

Table 6- 19 Return values

Value Variable

Description

0x00

BRP_OK

No error has occurred

0x01

BRP_ERR_STATUS

The reader has returned a status code that is

≠

"0".

0x02

BRP_ERR_BUSY

The reader is currently processing a function.

0x03

BRP_ERR_IDLE

The reader is waiting for a function.

0x04

BRP_ERR_TIMEOUT

The response time has been exceeded.

0x05

BRP_ERR_CORRUPTED_FRAME

A bad frame was detected.

0x06

BRP_ERR_UNEXPECTED_FRAME An unexpected frame was detected.

0x07

BRP_ERR_GENERAL_IO

The underlying serial port has caused an error.

0x08

BRP_ERR_BUFFER_OVERFLOW

The reader sent more data than expected.

0x09

BRP_ERR_NO_MORE_HANDLES

There is no free session key.

0x0A

BRP_ERR_INSUFFICIENT_MEM

There is not enough memory to generate a new

session key.

0x0B

BRP_ERR_WRONG_HANDLE

The specified session key does not exist.

0x0C

BRP_ERR_WRONG_PARAMETERS The parameters of a function are incorrect.

Содержание SIMATIC RF1000 Series














































































Результаты поиска

Содержание SIMATIC RF1000 Series

Отзывы:

Похожие инструкции для SIMATIC RF1000 Series

Бренды по названию

Популярные бренды

Siemens SIMATIC RF1000 Series, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC RF1000 Series

Отзывы:

Похожие инструкции для SIMATIC RF1000 Series

Бренды по названию

Популярные бренды