Siemens SIMATIC NET страница 44 Скачать руководство пользователя

Страница: 44 / 464

Configuration

3.1 System

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

Configuration Manual, 10/2015, C79000-G8976-C351-05

Syntax

Call the command without parameters:

show versions

Result

The following settings are displayed:

●

Basic device

●

Name

●

Revision

●

Order ID

●

Firmware

●

Bootloader

●

Description

●

Version

●

Date

3.1.2

clear counters

Description

With this command, you reset the counters of an interface.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Syntax

Call up the command with the following parameters:

clear counters [<interface-type><interface-id>]

The parameters have the following meaning:

Parameter

Description

Range of values / note

interface-type

Type or speed of the interface

Specify a valid interface.

interface-id

Module no. and port no. of the interface

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды