Siemens SIMATIC NET страница 422 Скачать руководство пользователя

Страница: 422 / 464

Security and authentication

10.2 WLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

422

Configuration Manual, 10/2015, C79000-G8976-C351-05

10.2.5.5

no vap security encryption (access point)

Description

With this command, you disable encryption with a fixed (unchanging) WEP key. This setting

is activated as default. You can only enable or disable encryption if you have selected "Open

System" for authentication.

Note
This command is available only in access point mode.

Requirement

●

The type of authentication is "

open-system

You are in the Interface Configuration mode of the VAP interface.
The command prompt is as follows:

cli (config-if-vapX-0-Y)#

Syntax

Call the command without parameter assignment:

no vap security encryption

Result

The encryption is disabled.

Further notes

You display the settings with the

show wlan security <vapX 0/Y>

command.

You enable the encryption with the

vap security encryption

command.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды