Siemens SIMATIC NET страница 351 Скачать руководство пользователя

Страница: 351 / 464

Network protocols

7.4 SNMP

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

351

7.4.2.22

snmp view

Description

With this command, you configure an SNMP view.

Requirement

●

An SNMP group has been created

●

The access to the group is configured with

snmp access

●

You are in the Global Configuration mode.

The command prompt is:

cli(config)#

Syntax

Call up the command with the following parameters:

snmp view <ViewName><OIDTree>[mask<OIDMask>]{included|excluded}

[{volatile|nonvolatile}]

The parameters have the following meaning:

Parameter

Description

Range of values / note

ViewName

Name of the SNMP view

max. 32 characters

OIDTree

Object ID

Path information of the MIB tree

mask

Keyword for the OID mask

OIDMask

Mask that filters access to the ele-

ments of the MIB tree

A series of "

" and "

" separated

by dots in keeping with the path

information of the MIB tree

View type

Specifies whether the filtered elements

are used or excluded

•

include

(Default)

•

excluded

Storage type

specifies whether the settings remain

following a restart:

•

volatile

(volatile):

The settings are lost after a

restart

•

nonvolatile

(non-volatile):

The settings are retained after

a restart (default)

If optional parameters are not specified when configuring, the default values apply.

Result

The SNMP view is configured.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды