Siemens SIMATIC NET SCALANCE XB-200 Series Скачать руководство пользователя страница 64

Страница: 64 / 78

8.10

Switching properties

The following switching properties listed are valid for SCALANCE XB-200.

Switching properties
Aging time

Can be configured (default value: 30 seconds)

Maximum frame size

1632

Max. number of learnable ad‐

dresses

8192

Response to LLDP frames

Blocking

Response to spanning tree

BPDU frames

Forwarding

CoS acc. to IEEE 802.1Q

Yes

QoS priority queues

Switching technique

Store and forward

Latency

10 microseconds

Full wire speed switching

Frame length (bytes)

Number of frames per second (at 100 Mbps)

148810

128

84459

256

45290

512

23496

1024

11973

1280

9615

1518

8127

Note
The number of SCALANCE XB-200 modules connected in a line influences the frame delay.

When a frame passes through the switch, this is delayed by the store-and-forward function of

the SCALANCE XB-200 by 10-130 microseconds (at 100 Mbps).

Technical specifications
8.10 Switching properties

SCALANCE XB-200

Operating Instructions, 03/2020, C79000-G8976-C359-09

Содержание SIMATIC NET SCALANCE XB-200 Series















































































Результаты поиска

Содержание SIMATIC NET SCALANCE XB-200 Series

Отзывы:

Похожие инструкции для SIMATIC NET SCALANCE XB-200 Series

Бренды по названию

Популярные бренды

Siemens SIMATIC NET SCALANCE XB-200 Series, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET SCALANCE XB-200 Series

Отзывы:

Похожие инструкции для SIMATIC NET SCALANCE XB-200 Series

Бренды по названию

Популярные бренды