Siemens SIMATIC NET RUGGEDCOM RST2228 Скачать руководство пользователя страница 45

Страница: 45 / 58

Technical Specifications
5.3 Failsafe Alarm Relay Specifications

Power In

Voltage Range

Internal

Fuse Rating

Power Out

Wire Gage

45-57 VDC

44-57 VDC, 15 W per Port

Maximum (IEEE 302.af)

The required wire size depends on the number of POE modules installed in the system and the

maximum current capability of the POE power source. Each POE module will draw up to 3A maximum

with a system maximum of 12A. Follow applicable local wiring codes and standards for minimum wire

gage.

5.3

Failsafe Alarm Relay Specifications

Maximum Switching Voltage

Rated Switching Current

Isolation

30 VDC

2 A

1.5kVAC

125 VDC

0.15 A

1.5kVAC

150 VAC

2 A

1.5kVAC

5.4

Supported Networking Standards

Parameter

10 Mbps

100

Mbps

1000

Mbps

10000

Mbps

Notes

IEEE 802.1AB

Link Layer Discov-

ery Protocol (LLDP)

IEEE 802.1D

MAC bridges

IEEE 802.1Q

VLAN (Virtual LAN)

IEEE 802.1p

Priority levels

IEEE 802.1x

Port-based net-

work access control

IEEE 802.3

10Base-T

IEEE 802.3u

100Base-TX/100Base-FX

IEEE 802.3z

1000Base-SX/LX

IEEE 802.3ab

1000Base-TX

IEEE 802.3ae

10GBase

IEEE 802.3af

Power over Ethernet ports

IEEE 802.3at

PoE+ ports, 4-pair

IEEE 802.3x

Full duplex operation

5.5

Operating Environment

The RUGGEDCOM RST2228P is rated to operate under the following environmental

conditions.

RUGGEDCOM RST2228P

Installation Manual, 12/2019, C79000-G8976-1403-05

Содержание SIMATIC NET RUGGEDCOM RST2228



























































Результаты поиска

Содержание SIMATIC NET RUGGEDCOM RST2228

Отзывы:

Похожие инструкции для SIMATIC NET RUGGEDCOM RST2228

Бренды по названию

Популярные бренды

Siemens SIMATIC NET RUGGEDCOM RST2228, Руководство по установке

Результаты поиска

Содержание SIMATIC NET RUGGEDCOM RST2228

Отзывы:

Похожие инструкции для SIMATIC NET RUGGEDCOM RST2228

Бренды по названию

Популярные бренды