Siemens SIMATIC NET RUGGEDCOM RSG2300 Скачать руководство пользователя страница 40

Страница: 40 / 54

Technical Specifications

This section details the specifications and operating conditions of the device.

5.1

Power Supply Specifications

The RUGGEDCOM RSG2300 can be equipped with the following power supplies:

NOTICE

Electrical hazard – risk of damage to the device

Make sure power input to the device is within the specified input range.

Input Range

Power

Supply Type

Minimum

Maximum

Internal Fuse

Rating

Maximum Power

Consumption

24 VDC

10 VDC

36 VDC

6.3 A(F)

48 VDC

36 VDC

59 VDC

3.15 A(T)

HI (125/250 VDC)

88 VDC

300 VDC

2 A(T)

HI (110/230 VAC)

85 VAC

264 VAC

2 A(T)

25 W

(F) denotes fast-acting fuse

(T) denotes time-delay fuse.

Power consumption varies based on configuration. 10/100Base-TX ports consume roughly 1 W less than

fiber optic ports.

The HI power supply is the same power supply for both AC and DC.

5.2

Failsafe Relay Specifications

Maximum Switching

Voltage

250 VAC, 125 VDC

Rated Switching

Current

2 A @ 250 VAC, 0.15 A @ 125 VDC, 2 A @ 30 VDC

Maximum Switching

Capacity

150 W, 500 VA

5.3

Supported Networking Standards

Standard

10 Mbps Ports

100 Mbps

Ports

1000 Mbps

Ports

Description

IEEE 802.3

10BaseT/10BaseFL

RUGGEDCOM RSG2300

Installation Manual, 04/2022, C79000-G8976-1046-18

Содержание SIMATIC NET RUGGEDCOM RSG2300























































Результаты поиска

Содержание SIMATIC NET RUGGEDCOM RSG2300

Отзывы:

Похожие инструкции для SIMATIC NET RUGGEDCOM RSG2300

Бренды по названию

Популярные бренды

Siemens SIMATIC NET RUGGEDCOM RSG2300, Руководство по установке

Результаты поиска

Содержание SIMATIC NET RUGGEDCOM RSG2300

Отзывы:

Похожие инструкции для SIMATIC NET RUGGEDCOM RSG2300

Бренды по названию

Популярные бренды