background image

Communication Ports
4.4.2 Removing a GBIC Optical Port

5. Squeeze the latches on either side of the port and insert the port into the socket.

2

1

3

     1    

GBIC Optical Port Module

     2    

Socket

     3    

Locking Latch

Figure 4.8

Installing a GBIC Optical Port

6. Release the latches and make sure the port is locked in place.

NOTICE

Only remove the dust plug when ready to connect a cable to the GBIC optical

port.

7. Remove the dust cover from the port and store for future use.
8. Remove the dust cap from the cable and immediately connect it to the port.
9. Connect the cable to a network and observe the LED associated with the port.

For more information about the LED, refer to 

"

Communication Ports

 (Page

23)"

.

4.4.2

Removing a GBIC Optical Port

To remove an GBIC optical port, do the following:

NOTICE

Electrical hazard – risk of damage to equipment

Make sure all electrostatic energy is dissipated before performing installing or

removing components from the device. An electrostatic discharge (ESD) can cause

serious damage to the component once it is outside the chassis.

1. Make sure all potential electrostatic build-up has been properly discharged to

prevent an electrostatic discharge (ESD). This can be accomplished by wearing

an ESD-preventive wrist trap connected to either the chassis ground connector

or a bare metal surface on the router/switch.

28

RUGGEDCOM RSG2200F

Installation Manual, 04/2022, C79000-G8976-1346-10

Содержание SIMATIC NET RUGGEDCOM RSG2200F























































Отзывы: