Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO Скачать руководство пользователя страница 75

Страница: 75 / 193

5 Display / WBM Configuration

IE/AS

−

INTERFACE LINK PN IO

as of hardware version 1, as of firmware version V2.0

Release 08/2018

C79000

−

G8976

−

C216

−

5.2.10

Navigation “Industrial Ethernet −> Ports”

5.2.10.1 Ports

Keypad/Display

IND. ETHERNET > Info > Ethernet Port 1 >

Link

(physical connection up/down)

Mode

(10/100 Mbps, half duplex/full duplex)

Input bytes

(number of received bytes)

Output bytes

(number of sent bytes)

> Ethernet Port 2 ... (as for Port 1)

WBM: “Ports” Tab − Port Status

This page informs you about the current status of the port.

Parameter

Function

Port

LAN interface of the IE/AS-i LINK

Type

Interface type (on the IE/AS-i LINK: type “TP 100 TX”)

Mode

Displays the transmission mode set by autonegotiation and made up of the

transmission rate (10 or 100 Mbps) and the transmission method (full duplex (FD)

or half duplex (HD)). Possible values: 10FD, 10HD, 100FD or 100HD

Desired Mode

Displays the desired mode (on the IE/AS-i LINK always: “AutoNegotiation”, in other

words negotiation of the transmission mode)

Status

Current port status (on the IE/AS-i LINK always: “forwarding”)

Desired Status

Display of the desired status of the port (for the IE/AS-i LINK always: “Enabled”)

Link

Status of the link to the network: Possible values:

The port has a valid link to the network, a link integrity signal is being received.

down

The port has no link to the network.

Содержание SIMATIC NET IE/AS-INTERFACE LINK PN IO


































































































































































































Результаты поиска

Содержание SIMATIC NET IE/AS-INTERFACE LINK PN IO

Отзывы:

Похожие инструкции для SIMATIC NET IE/AS-INTERFACE LINK PN IO

Бренды по названию

Популярные бренды

Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO, Руководство пользователя

Результаты поиска

Содержание SIMATIC NET IE/AS-INTERFACE LINK PN IO

Отзывы:

Похожие инструкции для SIMATIC NET IE/AS-INTERFACE LINK PN IO

Бренды по названию

Популярные бренды