Siemens SIMATIC NET CP 343-1 Скачать руководство пользователя страница 40

Страница: 40 / 78

Installation, connecting up and commissioning

5.3 Connecting the CP to Ethernet

CP 343-1

Manual, 12/2018,

C79000−G8976−C201

-08

TCP/IP protocol must be installed. The protocol used must then be applied to the S7ONLINE

access point.

Diagnostics

Use the diagnostic functions during commissioning and to analyze problems. The following

options are available:

●

The LED displays on the CP

●

Hardware diagnostics and troubleshooting with STEP 7

●

Communication diagnostics with STEP 7 / NCM Diagnostics

●

Static information using HW Config

●

Web diagnostics

●

If applicable, evaluation of the alarm block FB 54 in the user program

●

Queries via SNMP

5.3

Connecting the CP to Ethernet

Connecting interface X1 to Industrial Ethernet

Connect the CP to Industrial Ethernet via one of the RJ45 jacks.

Where necessary, connect another component to the remaining free RJ45 jack.

Содержание SIMATIC NET CP 343-1















































































Результаты поиска

Содержание SIMATIC NET CP 343-1

Отзывы:

Похожие инструкции для SIMATIC NET CP 343-1

Бренды по названию

Популярные бренды

Siemens SIMATIC NET CP 343-1, Руководство пользователя

Результаты поиска

Содержание SIMATIC NET CP 343-1

Отзывы:

Похожие инструкции для SIMATIC NET CP 343-1

Бренды по названию

Популярные бренды