Siemens SIMATIC NET CP 243-1 Скачать руководство пользователя страница 43

Страница: 43 / 142

CP 243-1
Operating Instructions, 03/2012, C79000-G8976-C244-02

Installation and commissioning

2.1

Important notes on installation and commissioning

Safety notices relating to the use of the device

The following safety notices must be adhered to when installing, commissioning, connecting,

replacing components and opening the device.

General information

WARNING

Safety extra-low voltage
The equipment is designed for operation with Safety Extra-Low Voltage (SELV) by a

Limited Power Source (LPS).
This means that only SELV / LPS complying with IEC 60950-1 / EN 60950-1 / VDE 0805-1

must be connected to the power supply terminals. The power supply unit for the equipment

power supply must comply with NEC Class 2, as described by the National Electrical Code

(r) (ANSI / NFPA 70).
There is an additional requirement if devices are operated with a redundant power supply:
If the equipment is connected to a redundant power supply (two separate power supplies),

both must meet these requirements.

General notices for use in hazardous areas

WARNING

Risk of explosion when connecting or disconnecting the device
EXPLOSION HAZARD
DO NOT CONNECT OR DISCONNECT EQUIPMENT WHEN A FLAMMABLE OR

COMBUSTIBLE ATMOSPHERE IS PRESENT.

Содержание SIMATIC NET CP 243-1















































































































































Результаты поиска

Содержание SIMATIC NET CP 243-1

Отзывы:

Похожие инструкции для SIMATIC NET CP 243-1

Бренды по названию

Популярные бренды

Siemens SIMATIC NET CP 243-1, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET CP 243-1

Отзывы:

Похожие инструкции для SIMATIC NET CP 243-1

Бренды по названию

Популярные бренды