Siemens SIMATIC NET 6GK5766-1GE00-3DA0 Скачать руководство пользователя страница 49

Страница: 49 / 82

SCALANCE WxM766
Operating Instructions, 03/2022, C79000-G8976-C617-03

Connection

6.1

Safety when connecting up

Safety notices

When connecting up the device, keep to the safety notices listed below.

Note
Close unused sockets

Close all unused M12 sockets with protective caps (tightening torque at least 0.4 Nm) to

achieve the specified type of protection.

Lightning protection

WARNING

Danger due to lightning strikes

Antennas installed outdoors must be within the area covered by a lightning protection

system. Make sure that all conducting systems entering from outdoors can be

protected by a lightning protection potential equalization system.
When implementing your lightning protection concept, make sure you adhere to the

VDE 0182 or IEC 62305 standard.

Suitable lightning protectors are available in the accessories (Page 28) of SIMATIC NET

Industrial WLAN.

Note

We recommend that you use the maintenance-free lightning protector LP798-2N.
Exception: When there is also DC power supplied via the antenna cable. In this case,

only the lightning protector LP798-1N can be used.

WARNING

Danger due to lightning strikes

Installing this lightning protector between an antenna and a SCALANCE W device is not

adequate protection against a lightning strike. The LP798-1N lightening protector only

works within the framework of a comprehensive lightning protection concept. If you

have questions, ask a qualified specialist company.

Содержание SIMATIC NET 6GK5766-1GE00-3DA0



















































































Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды

Siemens SIMATIC NET 6GK5766-1GE00-3DA0, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды