Siemens SIMATIC NET 6GK5766-1GE00-3DA0 Скачать руководство пользователя страница 28

Страница: 28 / 82

Description of the device

4.5 Accessories

SCALANCE WxM766

Operating Instructions, 03/2022, C79000-G8976-C617-03

Flexible connecting cable IWLAN QMA/N-Connect male/female

Adapter cable for connecting a MIMO antenna with QMA connectors to the flexible

connecting cables; preassembled with one QMA male and one N-Connect female

connector; scope of delivery 3 units:

Length

Article number

1 m

6XV1875-5JH10

For railway applications, the following connecting cable is available, scope of delivery 1

unit:

Length

Article number

1 m

6XV1875-5VH10

4.5.6.2

Lightning protection

Component

Description

Article number

LP798-1N

Lighting protector with N/N

female/female connector with gas

discharge technology

6GK5798-2LP00-2AA6

LP798-2N

Lighting protector with N/N

female/female connector with quarter

wave technology

6GK5798-2LP10-2AA6

4.5.6.3

Terminating resistor

Component

Description

Article number

TI795-1N

Electrical connector N-Connect, male
Pack of 1

6GK5795-1TN00-1AA0

4.5.6.4

Cabinet feedthrough

Component

Description

Article number

IE M12 Panel Feedthrough

4 x 2

Cabinet feedthrough for conversion

from M12 connector technology (X-

coded, IP65/67) to RJ-45 connector

technology (X-coded, IP20)
pack of 5

6GK1901-0DM40-2AA5

N-Connect/N-Connect

Female/Female Panel

Feedthrough

Cabinet feedthrough for wall

thicknesses up to 4.5 mm, two N-

Connect female connectors

6GK5798-2PP00-2AA6

N-Connect/SMA

Female/Female Panel

Feedthrough

Panel feedthrough for wall thicknesses

up to a maximum of 5.5 mm, two N-

Connect/SMA female connectors.

6GK5798-0PT00-2AA0

Содержание SIMATIC NET 6GK5766-1GE00-3DA0



















































































Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды

Siemens SIMATIC NET 6GK5766-1GE00-3DA0, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды