Siemens SIMATIC MV540 H Скачать руководство пользователя страница 63

Страница: 63 / 238

SIMATIC MV500
Operating Instructions, 06/2018, C79000-G8976-C494-01

Mounting

5.1

Notes on installation

Note
Creating optimal reading conditions
When you install the optical reader, make sure that the code to be read is visible to the

optical reader with the best possible quality. You can optimally set up and align the reader

using the WBM ("Application > Program > Image acquisition").

When installing the reader, pay attention to the following points:

●

The viewing angle to the code may vary from 40° to 90° and 80° to 90° depending on the

code type.
You can find more information on the viewing angle in the section "Performance

characteristics when reading codes (Page 34)". You can find information on optimal setup

and alignment of the reader in the section "Connecting and setting up the reader using

the PST (Page 90)".

●

Note that the mounting location and viewing angle may affect the readability of the code.
–

There must be as few reflections as possible in the code field.

–

The code field must be evenly lit without shadows.

●

Keep enough distance between the individual codes.

●

The distance between a two-dimensional code and image border must be at least 2 cell

widths (dot width or line width).

Mounting the SIMATIC MV500 optical reader

The optical readers are autonomous compact devices that need to be mounted in a suitable

location and only require a lens, a power supply cable and a communications connection.

The SIMATIC MV500 optical reader has threaded holes on the front and back, allowing

flexible mounting options.
To provide lighting when reading the codes, you have several options available. The

simplest and most space-saving option is a ring light that can be integrated in the protective

lens barrel.

Содержание SIMATIC MV540 H















































































































































































































































Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды

Siemens SIMATIC MV540 H, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды