Siemens SIMATIC IPC1047 Скачать руководство пользователя

Страница: 75 / 136

Device maintenance and repair

7.2 Maintenance

SIMATIC IPC1047
Operating Instructions, 09/2018, A5E45118479-AA

7.2.2

Remove the fan cover

Procedure

Open the front door (see

"Opening the front door

(Page 52)") until the marked lock

releases the fan cover.

Take hold of the recessed grip.

Open the fan cover in the

direction of the arrow.

7.2.3

Replacing filters

The filter pad is located behind the fan cover.

Note
You may only use filters of the same type. Information about the original spare parts for

SIMATIC PCs is available in the Internet at SIMATIC IPC after-sales information system

(

http://www.siemens.com/asis

Filter pads are available as a pack of 10 under the article number A5E37019277.

Requirement

●

The device is disconnected from the power supply, see section "Switching off the device

(Page 46)".

●

The front door is open, see section "Opening the front door (Page 52)".

●

The fan cover has been removed, see section "Remove the fan cover (Page 75)".

●

A filter pad from the pack of 10 A5E37019277

Procedure

Remove the filter pad from the fan cover.

Insert the new filter pad into the fan cover. It is inserted loosely in the fan cover. When

you insert the filter pad, make sure it lies evenly in the fan cover.

Replace the fan cover.

Содержание SIMATIC IPC1047









































































































































Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC1047, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды