Siemens SIMATIC Ident CB Gate Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 70

background image

SIMATIC Ident CB Gate
Operating Instructions, 08/2022, C79000-G8976-C671-01

25

Connecting

5

NOTICE
Connection by qualified personnel

The SIMATIC Ident CB Gate may only be connected by qualified personnel, taking into

account the documentation belonging to it.

Note
Installation, connection and commissioning by Siemens Service

Installation, connection and commissioning of the SIMATIC Ident CB Gate can be performed

by the Siemens Service team.

Note that the CB Gate has two or four antennas depending on the system variant.

5.1

Connecting the system components

The SIMATIC Ident CB Gate is delivered in a partially connected state. This applies in particular

to the control cabinet, in which all components are already connected.
The following components must be connected:
•

Connect RF650A antennas to the RF680R reader using the antenna connection cable.
Note that the number of antennas depends on the system variant of the SIMATIC Ident CB

Gate.

•

Connect the SITOP PSU6200 power supply unit to an external power supply.

•

If necessary, connect the CB Gate to a higher-level system (e.g. a controller or a PC) with

an Ethernet cable via the SCALANCE XB005 switch.

Required tools

The following tools are required:
•

Screwdriver

«
...
23
24
25
26
27
...
»

Содержание SIMATIC Ident CB Gate







































































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC Ident CB Gate

Бренд: Bang & Olufsen Страницы: 20

Бренд: Bang & Olufsen Страницы: 24

BeoSound Ouverture

Бренд: Bang & Olufsen Страницы: 44

Бренд: S&S Northern Страницы: 9

Бренд: S.R.Smith Страницы: 2

Бренд: M-system Страницы: 4

Бренд: JBL Страницы: 8

Бренд: Tokai Страницы: 20

BALBOA CS6000B Series

Бренд: HydroQuip Страницы: 32

AutoLift AL-6000S2

Бренд: AAQ Страницы: 36

Бренд: Vansco Страницы: 11

Бренд: Gage Страницы: 36

Бренд: AXEM Technology Страницы: 31

Бренд: Feig Electronic Страницы: 35

Бренд: Buffalo Страницы: 2

Бренд: Rotary Страницы: 64

Бренд: Huchez Страницы: 15

BACnet iSMA-B-MINI

Бренд: iSMA CONTROLLI Страницы: 114

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды