Siemens SENTRON PAC2200CLP Скачать руководство пользователя страница 75

Страница: 75 / 130

PAC2200CLP
Equipment Manual, 06/2021, L1V30820585B-02

Service and maintenance

The device requires no maintenance.

7.1

Cleaning

Clean the device as required. Use a dry cloth for this.

NOTICE
Damage may result from use of detergents.

Detergents can damage the device. Do not use detergents.

7.2

Calibration

The device has been calibrated by the manufacturer before shipping. Recalibration is not

required provided the environmental conditions are maintained.

7.3

Troubleshooting guide

Remedies for the resolution of faults

Fault

Remedies

Device is not working

•

Check power supply

•

Check fuse

Voltage or current measured values are not displayed

•

Check fuse

•

Check the configuration (see Parameterizing the device

(Page 60))

Voltage values are not plausible

•

Check the voltage taps at the different phases to deter-

mine whether or not voltage is present

Current values are not plausible

•

Check the settings and the wiring of the current trans-

former (if present) and correct if necessary

Содержание SENTRON PAC2200CLP



































































































































Результаты поиска

Содержание SENTRON PAC2200CLP

Отзывы:

Siemens SENTRON PAC2200CLP, Руководство по эксплуатации продукта, Страница: 75 / 130

Результаты поиска

Содержание SENTRON PAC2200CLP

Отзывы: