Siemens SCALANCE XR-500 Скачать руководство пользователя страница 87

Страница: 87 / 112

Technical data

8.2 Technical specifications of the SCALANCE XR526-8C

SCALANCE XR-500
Operating Instructions, 05/2017, A5E03275845-11

Technical specifications

Current consumption at 100 VAC

0.8 A

Current consumption at 240 VAC

0.42 A

Effective power loss

38 W

Properties

Not implemented redundantly

2 x 100 to 240 VAC

Design

IEC plug C14 with switch,
2-pin

Rated voltage

100 / 240 VAC

Voltage range

90 to 264 VAC

Frequency

60 Hz / 50 Hz

Frequency range

47 Hz to 63 Hz

Fusing

3.15 A / 250 V

Current consumption at 100 VAC

0.8 A

Current consumption at 240 VAC

0.42 A

Effective power loss

38 W

Properties

Implemented redundantly

Permitted ambient conditions
Ambient temperature
For devices with 24 VDC

When operating without pluggable

transceiver of the types LH, LH+, ELH

or ELH200
up to 2000 m

0 °C to +70 °C

When operating as of 2000 m

The maximum ambient temperature is

reduced by 5°C

During storage

-40

℃ to +85 ℃

During transportation

40 ℃ to +85 ℃

Ambient temperature
for devices with 100 to 240 VAC

When operating without pluggable

transceiver of the types LH, LH+, ELH

or ELH200
up to 2000 m

0 °C to +60 °C

When operating as of 2000 m

The maximum ambient temperature is

reduced by 5°C

During storage

40 ℃ to +85 ℃

During transportation

40 ℃ to +85 ℃

Relative humidity

During operation at 25 ℃

≤ 95%, no condensation

Design, dimensions and weight
Weight

2 x 24 VDC

3.9 kg

1 x 100 to 240 VAC

4.4 kg

2 x 100 to 240 VAC

4.7 kg

Degree of protection

IP20

Dimensions without brackets for

19" rack mounting (W x H x D)

446 x 44 x 305 mm (1 height unit)

Содержание SCALANCE XR-500

















































































































Результаты поиска

Содержание SCALANCE XR-500

Отзывы:

Похожие инструкции для SCALANCE XR-500

Бренды по названию

Популярные бренды

Siemens SCALANCE XR-500, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE XR-500

Отзывы:

Похожие инструкции для SCALANCE XR-500

Бренды по названию

Популярные бренды