Siemens SCALANCE XR-500 Скачать руководство пользователя страница 68

Страница: 68 / 112

Connecting

5.6 Out-of-band interface

SCALANCE XR-500

Operating Instructions, 05/2017, A5E03275845-11

Assignment of the terminal block

The supplied connecting cable has the following assignment:

Contact

Pin assignment of the RJ-11 plug

Pin assignment of the D-sub female con-

nector

TD (Transmit Data)

RD (Receive Data)

SG (Signal Ground)

RD (Receive Data)

SG (Signal Ground)

Note
Pin assignment of the RJ-11 jack on the device
The RJ-11 jack on the device has a pinout to match the RJ-11 plug of the supplied

connecting cable.

5.6

Out-of-band interface

Information on the out-of-band interface

●

The out-of-band interface is an RJ-45 Ethernet port on the CPU module. The out-of-band

interface is not used for routing or switching.

●

Access to the device is also possible independent of the other Ethernet ports.

●

The out-of-band interface allows direct IP access to the WBM of the device.

Содержание SCALANCE XR-500

















































































































Результаты поиска

Содержание SCALANCE XR-500

Отзывы:

Похожие инструкции для SCALANCE XR-500

Бренды по названию

Популярные бренды

Siemens SCALANCE XR-500, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE XR-500

Отзывы:

Похожие инструкции для SCALANCE XR-500

Бренды по названию

Популярные бренды