Siemens SCALANCE XR-500 Скачать руководство пользователя страница 23

Страница: 23 / 112

Description of the device

3.1 Product overview

SCALANCE XR-500
Operating Instructions, 05/2017, A5E03275845-11

SFP+ data cable
The following cables are available for SFP+ transceivers:

Component

Description

Article number

IE CABLE SFP+/SFP+

Preassembled IE cable with SFP+

plugs,
electrical, 10 Gbps,
pack of 1

Length 1 m

6GK5 980-3CB00-0AA1

Length 2 m

6GK5 980-3CB00-0AA2

Length 7 m

6GK5 980-3CB00-0AA7

The following devices have SFP+ slots:

●

SCALANCE XR526-8C

Note

Restriction with SFP+ transceivers for SCALANCE XR526-8C

If you use SFP+ transceivers identified with

with the SCALANCE XR526-8C, the

maximum ambient temperature is reduced to 50 ℃.

Note

Restriction for DFP+ transceivers for SCALANCE XR526-8C (2 x 24 VDC)

If you use SFP+ transceivers identified with

with the SCALANCE XR526-8C (2 x 24

C), the maximum ambient temperature is reduced to 60 ℃.

For further information on the ambient temperature, refer to sections “Permitted ambient

temperature (Page 19)“ and “Technical specifications of the SCALANCE XR526-8C

(Page 86)“.

●

SCALANCE XR528-6M

●

SCALANCE XR552-12M

3.1.2.2

Additional accessories for modular devices

The following additional accessories are available for devices SCALANCE XR528-6M and

SCALANCE XR552-12M:

Fan unit

Type

Properties

Article number

FAN597-1

For SCALANCE XR552-12M

6GK5 597-1AA00-8AA0

FAN597-2

For SCALANCE XR528-6M

6GK5 597-2AA00-8AA0

NOTICE
Operation only with fan unit
Use the devices SCALANCE XR528-6M and SCALANCE XR552-12M only with a correctly

fitted fan unit. Operation without the fan is not possible and would damage the device.

Содержание SCALANCE XR-500

















































































































Результаты поиска

Содержание SCALANCE XR-500

Отзывы:

Похожие инструкции для SCALANCE XR-500

Бренды по названию

Популярные бренды

Siemens SCALANCE XR-500, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE XR-500

Отзывы:

Похожие инструкции для SCALANCE XR-500

Бренды по названию

Популярные бренды