Siemens SCALANCE XP208EEC Скачать руководство пользователя страница 50

Страница: 50 / 96

5.4

Wall mounting

Installation

Figure 5-1

Wall mounting

To mount the device screwed from the back on a wall, follow the steps below:

1. Prepare the drill holes for mounting. For the precise dimensions, refer to the section

"Dimension drawings (Page 85)".

2. Bring the drill holes and the cutouts for the hexagon nuts together so that they cover the

same area.

3. Place the hexagon nuts in the corresponding cutouts. The nuts cannot be turned in the

cutouts.

4. Push the screws through the drill holes and screw them to the nuts.

5. Fit the connectors for the power supply, see the section "Power supply (Page 59)".

6. Fit the connectors for the signaling contact, refer to the section "Signaling contact

(Page 64)".

Removal

To remove the device from the wall, follow the steps below:

1. Disconnect all connected cables.

2. Loosen the screws.

Installation
5.4 Wall mounting

SCALANCE XP-200

Operating Instructions, 03/2021, C79000-G8976-C428-08

Содержание SCALANCE XP208EEC

































































































Результаты поиска

Содержание SCALANCE XP208EEC

Отзывы:

Похожие инструкции для SCALANCE XP208EEC

Бренды по названию

Популярные бренды

Siemens SCALANCE XP208EEC, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE XP208EEC

Отзывы:

Похожие инструкции для SCALANCE XP208EEC

Бренды по названию

Популярные бренды