Siemens RWF40 Series Скачать руководство пользователя страница 50

Страница: 50 / 56

50/56

CC1B7865E

February 10, 2000

Landis & Staefa Division

10. What to do, if ...

This is an indication that a measured value is not being acquired correctly.

)

The detection of measured value range crossings depends on the type of
sensor used.

Section 11.3.2 «Measured value circuit monitoring»

Display

Description

Cause / controller behavior / remedy

1999

60.0

7865p08/0200

Actual value display
(red) shows «1999»
flashing.
Setpoint display shows
the setpoint.

Overrange or underrange on analog
input 1.
The actual value is not being measured.
Controller initiates lockout.

Section 5.3 «Safety shutdown»

The limit comparator responds to analog
input 1 according to the configuration
(C113).

✱

Check the electrical connections for

open-circuit of sensor

1999

7865p10/0200

When analog input 3 is
configured for outside
temperature (C111) and
the measured value is
called up, the actual
value display (red)
shows «1999» flashing.

Overrange or underrange on analog
input 3.
The outside temperature is not being
measured!
The weather-dependent setpoint is
inactive!

✱

Check the electrical connections for

open-circuit of sensors

1999

SP.E

7865p09/0200

When analog input 2 is
configured (C111) and
the measured value is
called up, the process
value display (red)
shows «1999» flashing.

Overrange or underrange on analog
input 2.
The external setpoint is not being
measured. Controller initiates lockout

Section 5.3 «Safety shutdown»

✱

Check the electrical connections for

open-circuit of sensors

53.2

1999

7865p07/0200

Actual value display
(red) shows «XXXXXX».
Setpoint display (green)
shows «1999» flashing.

Overrange or underrange on analog
input 2.
The setpoint shift is not being measured.
Controller initiates lockout

Section 5.3 «Safety shutdown»

✱

Check the electrical connections for

open-circuit of sensor

10.1 ...numbers are flashing on the display

Содержание RWF40 Series

























































Результаты поиска

Содержание RWF40 Series

Отзывы:

Похожие инструкции для RWF40 Series

Бренды по названию

Популярные бренды

Siemens RWF40 Series, Руководство пользователя

Результаты поиска

Содержание RWF40 Series

Отзывы:

Похожие инструкции для RWF40 Series

Бренды по названию

Популярные бренды