Siemens RUGGEDCOM WIN5114 Скачать руководство пользователя

Страница: 31 / 32

RUGGEDCOM WIN5114-V

Installation Guide

Chapter 5

Certification

Environmental Type Tests

A copy of the Material Declaration is available online at

https://support.industry.siemens.com/cs/ww/en/

view/109738831

Section 5.2

Environmental Type Tests

The RUGGEDCOM WIN5114-V has passed the following environmental tests.

Test

Description

Test Levels

IEC 60068-2-1

Low Temperature

-25 °C for 72 hours

-40 °C (-40 °F) for 16 hours
-40 °C (-40 °F) for 72 hours

IEC 60068-2-2

High Temperature

55 °C (131 °F) for 72 hours
60 °C (140 °F) for 16 hours
70 °C (158 °F) for 72 hours

IEC 60068-2-11

MIL-STD-810F 509.4

Salt Fog

5% NaCI 35° 48h

IEC 60068-2-14

Temperature Change

-10 to 45 °C (14 to 113 °F) @ 0.5 °C/min (0.9 °F/min) for 2 cycles

-40 to -30 °C (-40 to -22 °F) @ 1 °C/min (1.8 °F/min) for 5 cycles

Water (Rain, Intensity)

0.01 m³/min (0.35 ft³/min @ 90 kPa (13 PSI) for 30 minutes

IEC 60068-2-18

IEC 529 (IP65/IP67)

Water (Rain)

0.01 m³/min @ 90 kPa (13 PSI) for 15 minutes

IEC 60068-2-6

Sine Vibration

Velocity: 5 mm/s

Displacement: 1.5 mm

Acceleration: 2 m/s²

Frequency Range: 5 to 62 Hz, 62 to 200 Hz

3 Axes

Duration: 3x5 sweep

Random Vibration (Class 4M5)

ASD: 0.04 m²/s³

12 to 12 dB/oct

Frequency Range: 5 to 10 Hz, 10 to 50, 50 to 100 Hz

3 axes, 30 min per axes

IEC 60068-2-64

Random Vibration

ASD: 1 m²/s³

-3 dB/oct

Frequency Range: 5 to 20 Hz, 20 to 200 Hz

3 axes, 30 min per axes

Shock (Class 4M5)

Spectrum: Half sine

Duration: 11 ms

Accelerator: 50 m/s²

100 shocks in each direction

IEC 60068-2-29

Shock

Spectrum: Half sine

Duration: 6 ms

Accelerator: 180 m/s²

Содержание RUGGEDCOM WIN5114

































Результаты поиска

Содержание RUGGEDCOM WIN5114

Отзывы:

Похожие инструкции для RUGGEDCOM WIN5114

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM WIN5114, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM WIN5114

Отзывы:

Похожие инструкции для RUGGEDCOM WIN5114

Бренды по названию

Популярные бренды