Siemens RUGGEDCOM RX1500 Скачать руководство пользователя страница 4

Страница: 4 / 68

Table of Contents

Preface ............................................................................................................................................ v

Related Documents ................................................................................................................. v

Accessing Documentation ....................................................................................................... v

Registered Trademarks ............................................................................................................ v

Warranty ................................................................................................................................ vi

Training .................................................................................................................................. vi

Customer Support .................................................................................................................. vi

Contacting Siemens ............................................................................................................... vii

Introduction ........................................................................................................................... 1

1.1

Feature Highlights ................................................................................................. 1

1.2

Description ............................................................................................................ 1

1.3

Required Tools and Materials ................................................................................. 3

1.4

Decommissioning and Disposal ............................................................................. 3

1.5

Cabling Recommendations .................................................................................... 3

1.5.1

Protection On Twisted-Pair Data Ports .................................................................... 4

1.5.2

Gigabit Ethernet 1000Base-TX Cabling Recommendations ...................................... 4

Installing the Device ............................................................................................................. 5

2.1

General Procedure ................................................................................................. 6

2.2

Unpacking the Device ........................................................................................... 6

2.3

Mounting the Device ............................................................................................. 7

2.3.1

Mounting the Device to a Rack .............................................................................. 7

2.3.2

Mounting the Device on a DIN Rail ........................................................................ 8

2.3.3

Mounting the Device to a Panel ............................................................................ 9

2.4

Connecting the Failsafe Alarm Relay .................................................................... 10

2.5

Connecting Power ............................................................................................... 11

2.5.1

Connecting High AC/DC Power ............................................................................ 12

2.5.2

Connecting Low DC Power .................................................................................. 15

Device Management ........................................................................................................... 21

3.1

Connecting to the Device .................................................................................... 21

3.2

Configuring the Device ........................................................................................ 22

3.3

Accessing the CompactFlash Card ........................................................................ 22

Modules ............................................................................................................................... 25

4.1

Requirements and Restrictions ............................................................................. 25

4.2

Available Modules ............................................................................................... 26

4.3

Installing/Removing Line Modules ........................................................................ 40

RUGGEDCOM RX1501

Installation Manual, 05/2020, C79000-G8976-1054-17

iii

Содержание RUGGEDCOM RX1500





































































Результаты поиска

Содержание RUGGEDCOM RX1500

Отзывы:

Похожие инструкции для RUGGEDCOM RX1500

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM RX1500, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM RX1500

Отзывы:

Похожие инструкции для RUGGEDCOM RX1500

Бренды по названию

Популярные бренды