Siemens RUGGEDCOM RS930L Скачать руководство пользователя страница 38

Страница: 38 / 48

Technical Specifications

5.5 Operating Environment

Wiring Standard

TIA/EIA T568A/B

Maximum Distance

100 m (328 ft)

Isolation

2.5 kV

Auto-negotiating.

Shielded or unshielded.

Auto-crossover and auto-polarity.

Typical distance. Dependent on the number of connectors and splices.

RMS 1 minute.

5.5

Operating Environment

The RUGGEDCOM RS930L is rated to operate under the following environmental

conditions.

Ambient Operating

Temperature

-40 to 85 °C (-40 to 185 °F)

Ambient Storage Temperature

-40 to 85 °C (-40 to 185 °F)

Ambient Relative Humidity

5% to 95%

Maximum Altitude

2000 m (6562 ft)

Measured from a 30 cm (12 in) radius surrounding the center of the enclosure.

Non-condensing.

5.6

Mechanical Specifications

Weight

1.2 kg (2.7 lbs)

Enclosure

20 AWG Galvanized Steel

5.7

Dimension Drawings

Note

All dimensions are in millimeters, unless otherwise stated.

RUGGEDCOM RS930L

Installation Manual, 04/2021, C79000-G8976-1034-09

Содержание RUGGEDCOM RS930L

















































Результаты поиска

Содержание RUGGEDCOM RS930L

Отзывы:

Похожие инструкции для RUGGEDCOM RS930L

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM RS930L, Руководство пользователя

Результаты поиска

Содержание RUGGEDCOM RS930L

Отзывы:

Похожие инструкции для RUGGEDCOM RS930L

Бренды по названию

Популярные бренды