Siemens RUGGEDCOM RMC20 Скачать руководство пользователя

Страница: 38 / 42

Certification

5.1.7 ACMA

5.1.7

ACMA

This device meets the requirements of the following Australian Communications and

Media Authority (ACMA) standards under certificate ABN 98 004 347 880:
• Radiocommunications (Compliance Labelling – Devices) Notice 2014 made

under Section 182 of the Radiocommunications Act 1992

• Radiocommunications Labelling (Electromagnetic Compatibility) Notice 2008

made under Section 182 of the Radiocommunications Act 1992

• Radiocommunications (Compliance Labelling – Electromagnetic Radiation)

Notice 2003 made under Section 182 of the Radiocommunications Act 1992

• Telecommunications Labelling (Customer Equipment and Customer Cabling)

Notice 2001 made under Section 407 of the Telecommunication Act 1997

The device is marked with an RCM symbol to indicate compliance when sold in the

Australian region.

A copy of the Declaration of Conformity is available via Siemens Industry Online

Support at

https://support.industry.siemens.com/cs/ww/en/view/89855782

5.1.8

RoHS

This device is declared by Siemens AG to meet the requirements of the following

RoHS (Restriction of Hazardous Substances) directives for the restricted use of certain

hazardous substances in electrical and electronic equipment:
•

China RoHS 2

Administrative Measure on the Control of Pollution Caused by Electronic

Information Products

A copy of the Material Declaration is available online at

https://

support.industry.siemens.com/cs/ww/en/view/109738831

5.1.9

Other Approvals

This device meets the requirements of the following additional standards:
•

IEEE 1613

IEEE Standard Environmental and Testing Requirements for Communications

Networking Devices in Electric Power Substations

•

IEC 61850-3

Communications Networks and Systems for Power Utility Automation – Part 3:

General Requirements

RUGGEDCOM RMC20

Installation Manual, 04/2021, C79000-G8976-1007-10

Содержание RUGGEDCOM RMC20











































Результаты поиска

Содержание RUGGEDCOM RMC20

Отзывы:

Похожие инструкции для RUGGEDCOM RMC20

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM RMC20, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM RMC20

Отзывы:

Похожие инструкции для RUGGEDCOM RMC20

Бренды по названию

Популярные бренды