background image

13/14 

Siemens 

Room temperature controllers with LCD 

N3075en 

Building Technologies 

 

17.04.2009 

Low-voltage directive 

Product standards 

Automatic electrical controls for household  
and similar use 
Special requirements for temperature- 
dependent controls 

 
EN 60730 – 1 
 
EN 60730 – 2 - 9 

Electromagnetic compatibility 
 Emissions 
 Immunity 

 
IEC/EN 61000-6-3 
IEC/EN 61000-6-2 

Devices of safety class 

II to EN 60730 

Degree of pollution 

Normal 

Degree of protection of housing 

IP30 to EN 60529 

Connection terminals for 

Solid wires or prepared stranded 
wires 2 x 0.4…1.5 mm

2

 or  

1 x 2.5 mm

2

 

Weight 0.28 

kg 

Color of housing front 

White, NCS S 0502-G (RAL 9003)

Connection terminals 

RDX33.21 

 

    Q13  Q14

Q22

 

 

Q13- Q14  Control output (NO), compressor 
Q21-Q22  Control output (NO), H/C changeover 

 

RDX43.2 

L

N   Q13  Q14

Q33  Q34

Q22

 

 
L, N 

 

Operating voltage AC 230 V 

Q13-Q14   

Control output (NO), compressor 

Q21-Q22       

Control output  (NO), H/C changeover for heating 

Q21-Q24    

Control output (NO), H/C changeover for cooling 

Q33-Q34                    Control output (NO), auxiliary electric heater

 

Connection diagrams 

Use:

 

H/C with RDX33.21

 

H/C plus auxiliary electric heating with RDX43.2

 

Heat pump

 

 

N1

Q13

Q14

Q21

Q22

DC 3 V

*

 

Q34

N2

L

L

N

N

AC

 23

V

Q13

Q33

Q14

Q21

Q22

Q24

*

 

H/C with  
actuating devices

 

N1

Q13

Q14

Lx

N

Q21

Q22

A

C

 2

4

...

 2

3

V

DC 3 V

R1

*

 

L

N

Q33

Q13

L

N

Q21

A

C

 23

0 V

N2

E1

Q14

Q22

Q24

Q34

*

 

General 

Содержание RDX33.21















Отзывы: