Siemens NK8237 MP4.40 Скачать руководство пользователя страница 13

Страница: 13 / 68

Structure and functions

Building Technologies

048_DMS_NK8237_ICC_MP4.40_A6V10316241_a_en.doc

Fire Safety & Security Products

06.2011

The four LED's on the right side are, from top to bottom:

Front panel LED (right

Functions

Com1

Status Com1

Com2

Status Com2

Com3 (not used)

Status Com3

Com4 (not used)

Status Com4

Red:

Green:

Tab.2.LED functions on the front panel, right side

4.1.2

Internal DIP switches

The internal DIP switches (S101) enable a download session via FTP using a de-
fault IP address.

Internal switch

Functions

DIP switch 1

Default mode/network access:
If DIP-switch 1 is ON, an FTP connection occurs by default on the
Ethernet at the default IP address 192.168.9.41.

DIP switch 2

Default mode/network access:
If DIP-switch 2 is ON, an FTP connection occurs by default on the
Ethernet at the default IP address 192.168.10.41.

Tab.3.Internal DIP switches

4.1.3

Internal jumpers

The internal jumpers (see Fig. 4) are used for:



X115: When closed, it disables the box tamper alarm;

Fig. 4 NK823x internal DIP switch and jumpers (NKM8001-A1 mainboard)

X104

X103

S101: DIP-Switches

S2: Tamper switch

S1: Reset button

X101

X102

X11

X105

Содержание NK8237 MP4.40





































































Результаты поиска

Содержание NK8237 MP4.40

Отзывы:

Siemens NK8237 MP4.40, Установка, Функции и Настройка, Пусконаладка, Страница: 13 / 68

Результаты поиска

Содержание NK8237 MP4.40

Отзывы: