Basic operation
en
7
2.
Slide your finger to the right over the settings range
until
appears in the display.
a
After approx. six minutes, the appliance automatic-
ally switches to a lower fan setting.
6.7 Switching off intensive mode, variant 1
▶
Press until the required fan setting is reached.
a
Intensive mode is ended early.
6.8 Switching off intensive mode, variant 2
▶
Slide your finger to the left over the
settings
range until the required fan setting is reached.
a
Intensive mode is ended early.
6.9 Switching on the boost function
The boost function is a short-term maximum power set-
ting which can be activated in any fan setting.
▶
Press .
a
After approx. 20 seconds, the fan automatically
switches back to the fan setting that was previously
set.
6.10 Switching on the fan run-on, variant 1
During the fan run-on, the appliance continues to run
for a short time and then switches off automatically.
▶
Press or slide in the filter pull-out.
a
The appliance switches off automatically after ap-
prox. 10 minutes.
6.11 Switching on the fan run-on, variant 2
During the fan run-on, the appliance continues to run
for a short time and then switches off automatically.
▶
Slide in the filter pull-out.
a
The appliance switches off automatically after ap-
prox. 10 minutes.
6.12 Switching on automatic mode
1
The optimum fan setting is set automatically using a
sensor.
▶
Press
.
6.13 Switching off automatic mode
1
▶
Press
or .
a
The ventilation is automatically ended when the
sensor detects no further change in the room air
quality.
a
Automatic mode runs for a maximum of four hours.
6.14 Switching on the lighting
The lighting can be switched on and off independently
of the ventilation system.
▶
Press .
6.15 Setting the brightness
▶
Press and hold until the required brightness is
reached.
6.16 Switching on the audible signal
▶
Press and hold and at the same time for ap-
prox. three seconds until a signal sounds.
6.17 Switching off the audible signal
▶
Press and hold and at the same time for ap-
prox. three seconds until a signal sounds.
6.18 Sensor control
1
In automatic mode, a sensor in the appliance detects
the intensity of the cooking and roasting fumes. De-
pending on the setting of the sensor sensitivity, the op-
timum fan setting is automatically switched on. If the
sensor control system reacts too weakly or too
strongly, the setting for the sensor sensitivity may
change.
¡
Factory setting: 3
¡
Lowest setting: 1
¡
Highest setting: 5
6.19 Setting the sensor control
1
Requirement:
The appliance is switched off.
1.
Press and hold
for approx. four seconds until
the setting is displayed.
2.
To change the setting, slide your finger over the set-
tings range
.
3.
To save the setting, press and hold
for ap-
prox. four seconds.
6.20 Resetting the saturation indicator
After cleaning the grease filter or after changing the
odour filter, the saturation indicator can be reset.
Requirements
¡
After the appliance has been switched off, ap-
pears in the display for the grease filter.
¡
After the appliance has been switched off, ap-
pears in the display for the odour filter.
¡
A signal sounds repeatedly.
▶
Press .
a
The saturation indicator is reset.
6.21 Setting the saturation indicator,
variant 1
The saturation indicator must be adjusted depending
on the filter used.
Requirement:
The appliance is switched off.
1.
To set circulating-air mode for the standard odour
filter, press and hold and until appears in
the display.
2.
To set circulating-air mode for the CleanAir standard
odour filter or the CleanAir Plus odour filter, press
and hold and repeatedly until appears in
the display.
1
Depending on the appliance specifications
