Siemens KNX OZW775 V2.0 Скачать руководство пользователя страница 14

Страница: 14 / 18

Universal inputs

continued

Requirements for pulse inputs

Signal cables
Signal coupling
Type of contact
Mechanical signal source (Reed contact)
Max. pulse frequency
Min. pulse duration
Electronic signal source
Max. pulse frequency
Min. pulse duration
Insulating strength against mains potential

Recommendation: Shielded cables
Potential-free
Impulse contact

25 Hz
20 ms (incl. max. 10 ms bounce time)

100 Hz
5 ms
AC 3750 V as per EN 60950-1

Line length for:

Passive sensor signals LG-Ni 1000, T1, Pt 1000
Active signals DC 0…10 V
Status and impulse contacts

Max. 300 m
See data for signal-sending device
300 m

Relay outputs
Q1_,Q2_,Q3_,Q4_,Q7_,Q8_

Number

Relay with NC contact

Relay with NO contact

4 (terminals Q11,Q12 Q21,Q22,

Q31,Q32 Q41,Q42)

2 (terminals Q73,Q74 Q83,Q84)

External supply line fusing

NC contact, non-renewable fuse (slow)
NO contact, non-renewable fuse (slow)
Automatic line cutout
Release characteristic

Max. 3.15 A
Max. 5 A
Max. 13 A
B, C, D as per EN 60898

Line length

Max. 300 m

Relay contact data

Switching voltage
AC current (NC)
AC current (NO)
At 250 V
At 19 V
Switch-on current

Max. AC 250 V, min. AC 19 V
Max. 2 A ohm., 2 A ind. (cos

= 0.6)

Max. 4 A ohm., 3 A ind. (cos

= 0.6)

Min. 5 mA
Min. 20 mA
Max. 10 A (1 s)

Contact life at AC 250 V

At 0.1 A ohm.
At 0.5 A ohm.

At 2 A ohm.

At 4 A ohm.
Red. fact. at ind. (cos

= 0.6)

Guide values:
2 x 10

switchings

(NC and NO)

2 x 10

switchings (NC)

4 x 10

switchings (NO)

3 x 10

switchings (NC)

6 x 10

switchings (NO)

3 x 10

switchings (NO only)

0.85 (NC and NO)

Insulating strength between:

Relay contacts and system electronics (reinforced insulation)
Neighboring relay contacts (operational insulation)

AC 3750 V, as per EN 60950-1
AC 1250 V, as per EN 60950-1

AC 230 V

Screw terminals for:

Solid / stranded wire (twisted or with ferrule)
1 solid / stranded wire per terminal
2 solid / stranded wires per terminal (max. 2)

Min. Ø 0.8 mm
0.5...2.5 mm

0.5...1.5 mm

Connecting terminals

Inputs and outputs

PC interface

Interface

Standard
Device class

Baud rate

USB V1.1 (universal serial bus)
RNDIS (remote network device
Interface specification)
Max. 12 Mbps (full speed)

Connecting cable for operator station

Cable length
Cable type for connection to PC/laptop
Cable type for connection to OZW775

Max. 5 m
USB type A
USB type B

Modem interface

Interface

Standard
Baud rate

RS-232, V.24 / EIA 232D
Max. 115 kbaud

Connecting cable for modem

Cable length
Cable type for connection to OZW775

Max. 15 m
D-sub 9-pin, plugs

14/18

Building Technologies

Central communication unit OZW775 V2.0

CE1N5663en

HVAC Products

29.10.2008

Содержание KNX OZW775 V2.0



















Результаты поиска

Содержание KNX OZW775 V2.0

Отзывы:

Похожие инструкции для KNX OZW775 V2.0

Бренды по названию

Популярные бренды

Siemens KNX OZW775 V2.0, Быстрый старт

Результаты поиска

Содержание KNX OZW775 V2.0

Отзывы:

Похожие инструкции для KNX OZW775 V2.0

Бренды по названию

Популярные бренды