Siemens Insys 56k Скачать руководство пользователя страница 42

Страница: 42 / 84

AT commands

Pocket Modem 56k

Dezember 05

Command Description

AT\K

Break control

The modem reacts to a break (receive path off for a certain amount of time), which it
receives from another modem or from the PC, or from the command

AT\B

according

to the parameters.

1. Situation

In case of a break from the PC during the data connection to another
modem:

AT\K0

Modem enters the command mode and sends no break to the other
modem.

AT\K1

Modem deletes the data buffer and sends a break to the other modem.

AT\K2

See

AT\K1

AT\K3

Modem immediately sends break to the other modem; data buffers are
not deleted.

AT\K4

See

AT\K0

AT\K5

Modem inserts break into the data transmitted to the other modem.

2. Situation

During a data connection, the modem was put into command mode by
an escape sequence

+++.

In this condition, the command

AT\B

will

send a break to the other modem. In this situation, the parameter n will
cause the following:

AT\K0

Modem deletes the data buffer and sends a break to the other modem

AT\K1

See

AT\K0

AT\K2

Modem sends break to the other modem without delay.

AT\K3

See

AT\K2

AT\K4

Modem inserts break into the data transmitted to the other modem

AT\K5

See

AT\K4

– Return from the online command mode into the data

mode via the ATO

command

3. Situation

In the case a break is received from another modem during a connection
that has not been error corrected, the parameters cause the following:

AT\K0

Modem deletes the data buffer and sends a break to the PC

AT\K1

See

AT\K0

AT\K2

Modem sends a break to the PC without delay.

AT\K3

See

AT\K2

AT\K4

Modem sends a break to the PC, which is embedded into the data that
was received from the other modem.

AT\K5

AT\K4

Содержание Insys 56k





















































































Результаты поиска

Содержание Insys 56k

Отзывы:

Похожие инструкции для Insys 56k

Бренды по названию

Популярные бренды

Siemens Insys 56k, Руководство по эксплуатации

Результаты поиска

Содержание Insys 56k

Отзывы:

Похожие инструкции для Insys 56k

Бренды по названию

Популярные бренды