en
Steaming
18
a
The appliance starts to heat and the time counts
down.
a
When the time has elapsed, a signal tone sounds. A
message appears on the display confirming that the
operation has finished.
9.
Once the cooking time has elapsed:
‒
If required, you can select other settings and re-
start the operation.
‒
When the food is ready, use to switch the ap-
pliance off.
10.
Empty the water tank and dry the cooking compart-
ment.
"After using steam operation", Page 18
Changing the type of heating
When you change the type of heating, the other set-
tings are also reset.
1.
Press
.
2.
Press
.
3.
Press the type of heating that you want to use.
4.
Reset the operation and use
to start.
Changing the temperature
Once the operation has started, you can change the
temperature at any time.
1.
Press the temperature.
2.
Change the temperature using or or via the ad-
justment bar. Or enter the temperature directly via
the number field .
3.
Press "Apply".
Changing the cooking time
You can change the cooking time at any time.
1.
Press the cooking time.
2.
Change the cooking time using or , or via the
adjustment bar. Or enter the temperature directly via
the number field .
3.
Press "Apply".
11.4 Setting added steam
Requirements
¡
Observe the information about the respective operat-
ing mode.
"Setting options with steam", Page 17
¡
The water tank has been filled. If the water tank runs
dry during operation, a message appears on the dis-
play. The appliance continues to operate but without
injecting steam into the cooking compartment.
"Filling the water tank", Page 16
1.
Press the operating mode that you require.
2.
Select the settings for the operating mode, e.g. type
of heating and temperature.
3.
Press "Added Steam" .
4.
Press the required steam level.
Steam level
Added steam
1
Low
2
Medium
3
High
5.
Press "Apply".
6.
Press
to start the operation.
a
The appliance starts heating.
a
The setting values and how long the appliance has
already been in operation are shown on the display.
7.
When the food is ready, use to switch the appli-
ance off.
8.
Empty the water tank and dry the cooking compart-
ment.
"After using steam operation", Page 18
Changing added steam
You can change or deactivate the added steam func-
tion at any time.
1.
Press the steam level.
2.
Change or deactivate added steam.
3.
Press "Apply".
11.5 Setting the steam jet function
Requirements
¡
Observe the information about the respective operat-
ing mode.
"Setting options with steam", Page 17
¡
The water tank has been filled. If the water tank runs
dry during operation, a message appears on the dis-
play. Operation is stopped.
"Filling the water tank", Page 16
1.
Press the operating mode that you require.
2.
Select the settings for the operating mode, e.g. type
of heating and temperature.
3.
Start the operation.
4.
Press "Steam jet" at the desired time.
a
The appliance starts to heat the water.
5.
When the water is heated up, press "Steam jet"
again.
a
The steam jet is triggered and the appliance adds
clouds of steam to the cooking compartment for ap-
prox. 3 to 5 minutes.
a
When the steam jet has finished, the operation con-
tinues to run as normal. Depending on the opera-
tion, the steam jet can be triggered again if neces-
sary.
6.
When the food is ready, use to switch the appli-
ance off.
7.
Empty the water tank and dry the cooking compart-
ment.
"After using steam operation", Page 18
Cancelling the steam jet
You can cancel the steam jet at any time.
▶
Press "Steam jet" .
a
"Steam jet" "Off" appears in the display.
a
The operation continues without the steam jet.
11.6 After using steam operation
Dry the appliance after each steam operation.
Note:
Traces of limescale may remain in the cooking
compartment after operation with steam. The functional-
ity of the appliance is not affected by this. You can re-
move traces of limescale using hot water or a cloth
soaked in vinegar. Observe the information on clean-
ing.
