Siemens Gigaset AD180, Руководство пользователя, Страница: 11 / 16

11
AL180 / IM-NORD EN / A31008-M2003-R201-1-9W19 / main.fm / 21.10.2008
Appendix
Entering letters/characters
Press the relevant key the number of times indi-
cated.
Briefly press the hash key
#
to switch from
"Abc" to "123" mode, from "123" to "abc"mode and
from "abc" to "Abc" mode.
Standard characters
1) Space
Specifications
Recommended batteries
Technology: Nickel-metal-hydride (NiMH)
Size: AAA (Micro, HR03)
Voltage: 1.2 V
Capacity: 400–800 mAh
We recommend the following types of battery:
◆
GP 550/700 mAh
◆
Yuasa Phone 700/800 mAh
◆
Peacebay 550/650 mAh
(Valid at the time of going to press)
The handset is supplied with recommended batter-
ies.
Base station power consumption
General specifications
Questions and answers
If you have any queries about the use of your tele-
phone, visit our website at
www.gigaset.com/customercare
for 24-hour support. The table below contains a list
of common problems and possible solutions.
Authorisation
This device is intended for analogue phone lines in
your network.
Country-specific requirements have been taken
into consideration.
We, Gigaset Communications GmbH, declare that
this device meets the essential requirements and
other relevant regulations laid down in Directive
1999/5/EC.
A copy of the 1999/5/EC Declaration of Conformity
is available at this Internet address:
www.gigaset.com/docs.
1x 2x 3x 4x 5x 6x 7x 8x 9x 10x 11x 12x 13x 14x
1
1 £ $ ¥ ¤
2
a b c 2 ä á à â ã ç
I
d e f 3 ë é è ê
4
g h i 4 ï í ì î
5
j k l 5
L
m n o 6 ö ñ ó ò ô õ
M
p q r s 7 ß
N
t u v 8 ü ú ù û
O
w x y z 9 ÿ ý æ ø å
Q
. , ? ! 0 + - : ¿ ¡ " ’ ; _
P
* / ( ) < = > %
#
Abc
-->
123
123
-->
abc
# @ \ & §
In standby mode
– Handset in base station
– Handset outside base station
approx. 1.3 W
approx. 1.3 W
During a call approx. 1.5 W
DECT standard is supported
GAP standard is supported
Range up to 300 m outdoors
up to 50 m indoors
Base station power supply 230 V ~/50 Hz
Environmental conditions
in operation
+5 °C to +45 °C, 20% to
75% elative humidity
1)
Problem Cause Solution
Nothing
appears in
the display.
The handset is not
switched on.
The batteries are
flat.
Press the end call
key
a
for approx.
5 seconds or place
the handset in the
base station.
Charge or replace the
batteries.
No wireless
connection
to the base
station,
Base flashes
in the display.
The handset is
outside the range
of the base sta-
tion.
The handset is not
registered.
The base station is
not turned on.
Move the handset
closer to the base
station.
Register the handset
¢
p. 9.
Check the mains con-
nector on the base
station
¢
p. 3.
You cannot
hear a ringer/
dialling tone
from the fixed
line network.
The phone cord
supplied has not
been used or has
been replaced by
a new cord with
the wrong jack
connections.
Please always use the
phone cord supplied
or ensure that the
pin connections are
correct when purchas-
ing from a retailer:
3-4 assignment of
telephone leads/
EURO CTR37.
Error tone
sounds after
system PIN
prompt.
PIN forgotten.
The system PIN
you have entered
is incorrect.
Reset the system PIN
to the default 0000
¢
p. 10.
All handsets are
de-registered. All
settings are reset.
All lists are deleted.