Issued by
Siemens Industry, Inc.
Building Technology Division
8 Fernwood Road
Florham Park, NJ 08932
Tel. +1 973-593-2600
www.sbt.siemens.com/FIS
@2016 Siemens Industry, Inc.
Technical specifications and availability subject to change without notice.
Doc No.
A6V10456397_enUS_c
101590209
Edition
2016-06-16
Intended use
The FT2008/FT2009 LED annunciator enables the fire
detection system to be displayed and operated in a
simplified way. The FT2008 provides 2×16 LEDs to
display alarm/trouble events. The FT2009 provides 2×32
LEDs to display alarm/trouble events. Both devices are
operated on the UFP line.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Package contents
The following are included in the scope of delivery:
l
FT2008-U1/FT2008-R1 or FT2009-U1/FT2009-R1
l
Cable ties (2 pcs)
l
EOL jumper connecter (1 pcs)
Safety instructions
Risk of injury to persons and damage to property
Please observe the following safety instructions:
l
The devices are only intended for stationary installation
in dry rooms.
l
The devices may only be connected to the UFP line.
l
If panel AUX power is not used, an UL listed/recognized
for fire use, regulated, power limited 24V DC power
supply is required.
l
Static discharge precautions should be taken when
handling the FT2008/FT2009.
Legend
1
Stub for mounting cover (2 pcs.)
2 Shield
terminal
3 Earth ground terminal
4 Mounting holes (8 pcs.)
5 Cable tie point
6 Breakout openings for cables (2 pcs.)
7 Holes for hanging front panel over stub (2 pcs.)
8 Dip-switch
9 Screws (2 pcs.)
10 EOL jumper
11 Connection terminals for UFP line and power supply
12 Front panel earth ground connection
Mounting instruction
1.
Break out the required cable openings (6) on the
backbox.
2.
Mark the drilling points for the 3 mounting holes (4), drill
the holes and insert the anchors (not supplied); or use
the pre drilled mounting holes for installation on a 2
gang, or 4” square standard electrical box.
3.
Pull the cables for the UFP and power supply, through
the breakout openings (6) on the backbox.
4.
Screw the backbox tightly in place.
5.
Connect the cable to the terminal (11) in accordance
with the connection diagram.
6.
Configure Dip-switch (8) and EOL jumper (10).
7.
Connect the green earth ground cable from front panel
(12) to backbox (3).
8.
Hook the front panel with the holes (7) over the stubs (1)
on the backbox.
9.
Press the front panel down over the backbox, screw (9)
upwards and fix the front panel in place.
Dip-switch
8-digit Dip-switch is used for setting address and baud rate.
The first 1-4 digits are for setting address, the 7-8 digits are
for setting UFP communication baud rate. The 5-6 digits are
reserved for future use.
Add.
Dip-switch
Baud Rate
Dip-switch
1 2 3 4
7
8
1
On Off Off Off
9600 bps
Off Off
2 Off On Off Off
19200 bps
On Off
3
On On Off Off
38400
bps Off
On
4 Off Off On Off
57600 bps
On
On
5
On Off On Off
6 Off On On Off
7
On On On Off
8 Off Off Off On
Technical data
FT2008
FT2009
Weight
2.646 lb
3.748 lb
Dimensions (W x H x D)
(In: inch)
8.110x7.362
x1.949
11.417x7.362
x1.949
Storage temperature
14…140 °F
Operating temperature
32…120.2 °F
Humidity
≤93% rel.
Housing
IP30
Operating voltage
24V DC Nominal
18.8…27.2V DC
Operating current
25 mA
25 mA
Activation current
65 mA
105 mA