Siemens FN2012-A1 Скачать руководство пользователя

Страница: 31 / 34

Adjustment elements

31 | 34

Building Technologies

A6V10407862_d_en_--

Siemens Industry, Inc.

2018-09-07

Rotary switch for device configuration

Configuration via the rotary switch is required for an Ethernet switch that is not

integrated into a panel. As an integrated Ethernet switch, the rotary switch must be

set to '0'.

By using the rotary switch for device configuration, the Ethernet switch can be set to

predefined network addresses or operation modes.
To accept a new configuration, the switch must be in a de-energized state when the

setting is made or a hardware reset must be performed afterward.

Switch position

IP address/operating mode

Sub-net mask/operating mode

Configured via web interface or MoNet

bus
Factory setting: 0.0.0.0

Configured via web interface or MoNet

bus
Factory setting: 255.255.248.0

192.168.99.241

255.255.248.0

192.168.99.242

255.255.248.0

192.168.99.243

255.255.248.0

192.168.99.244

255.255.248.0

192.168.99.245

255.255.248.0

192.168.99.246

255.255.248.0

192.168.99.247

255.255.248.0

192.168.99.248

255.255.248.0

192.168.99.249

255.255.248.0

192.168.99.250

255.255.248.0

192.168.99.251

255.255.248.0

192.168.99.252

255.255.248.0

Reserved (0.0.0.0)

Reserved (255.255.255.255)

Repeater mode

192.168.200.4

255.255.255.0

Содержание FN2012-A1



































Результаты поиска

Содержание FN2012-A1

Отзывы:

Похожие инструкции для FN2012-A1

Бренды по названию

Популярные бренды

Siemens FN2012-A1, Монтаж и установка

Результаты поиска

Содержание FN2012-A1

Отзывы:

Похожие инструкции для FN2012-A1

Бренды по названию

Популярные бренды