Siemens Flange Mount Kit Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 28

Siemens Flange Mount Kit Скачать руководство пользователя страница 1

DPD01156B

Siemens Industry, Inc.

1

Flange Mount Kits for Frames FS4 to FS7

Mounting Instructions

General

Using the optional Flange Mounting Kit, you can mount your drive through the cabinet wall or similar surface
so that the control unit of the drive remains inside the cabinet.

The correct installation of the Flange Mounting Kit might affect the IP or UL protection class of the drive. If
your drive is protected according to Type12/IP54, or your drive is supplied with flange option at the factory,
you only need to install the collars, as instructed. However, the power module of a Type1/IP21-protected drive
will only become protected according to Type12/IP54 on the rear side (see figure below), if all parts of the
flange mounting kit are installed properly. The need for this has to be evaluated and these actions are
explained in this guide.

Figure 1. Example of the flange mounting.

B

T

9070

CABINET WALL
OR SIMILAR

CABINET
WALL OR
SIMILAR

REAR
TYPE 12/
IP54

IP00

FRONT

1
2
3
...
»

Содержание Flange Mount Kit





























Отзывы:

Нет отзывов