Siemens FDCIO422 Скачать руководство пользователя страница 8

Страница: 8 / 8

Siemens Industry, Inc.

Building Technologies Division

8, Fernwood Road

Florham Park, New Jersey 07932

www.siemens.com/buildingtechnologies

Siemens Canada Limited

Building Technologies Division

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 Canada

Siemens Industry, Inc. 2012-201

Data and design subject to change without notice.

Document ID

Edition

A6V10324662_g_en_US

201

-0

End of Line Resistor Wiring Overview

①

CAUTION: FOR SYSTEM SUPERVISION – FOR TERMINALS IDENTIFIED WITH A

①

DO NOT USE

LOOPED WIRE TERMINALS. BREAK WIRE RUN TO PROVIDE SUPERVISION OF CONNECTIONS.

②

Use Siemens TB-EOL terminal P/N S54322-F4-A2 or equivalent.

③

Use only normally open dry contact SWITCHES for the inputs

Figure 11 Wiring end of line and switch

Use a 4 or 2 pole UL/ULC recognized SWITCH.

Switch Terminal must be capable of two conductors at one terminal.

EOL Resistor wiring must be done according to UL 864 and ULC-S527, chapter ‘EOL Devices’.

The EOL Resistors must be connected at the end of the input lines.

No addressable device or 2-wire smoke detectors can be connected to the inputs.

ACCESSORIES

DEVICE

ORDER NO.

EOL resistor 100

Ω

±1% ½ W

S54312-F7-A1

SIEMENS INDUSTRY, INC.

-inch adapter plate (optional)

M-411000

RANDL INDUSTRIES, INC.

5-inch Box (optional)

T55017

RANDL INDUSTRIES, INC.

5-inch Box (optional)

T55018

RANDL INDUSTRIES, INC.

5-inch Box (optional)

T55019

RANDL INDUSTRIES, INC.

TB-EOL terminal

S54322-F4-A2

SIEMENS INDUSTRY, INC.

SHIELDED W IRE MAX: 200 FT
18 - 14 AWG
OPEN AND SHORT SUPERVISION

OPEN

CLASS B STYLE C, OPEN AND SHORT WIRING SUPERVISION

SHIELDED W IRE MAX: 200 FT
18 - 14 AWG

OPEN SUPERVISION

OPEN

IN1 - 4

EARTH
GND

CLASS A STYLE D, OPEN WIRING SUPERVISION

CAUTION: BE AWARE OF THE INPUT POLARITY IN CLASS A MODE

SHIELDED W IRE MAX: 200 FT
18 - 14 AWG

OPEN

EARTH
GND

CLASS B STYLE B, OPEN WIRING SUPERVISION

OPEN SUPERVISION

EARTH
GND

470

100

470

for UL:

mount EOL directly on the last SWITCH terminal

for ULC:

mount EOL on the TB-EOL terminal

①

TB-EOL

②

TB-EOL

②

SW ITCH

③

SW ITCH

③

SW ITCH

③

①

③

SW ITCH

①

Содержание FDCIO422









Результаты поиска

Содержание FDCIO422

Отзывы:

Похожие инструкции для FDCIO422

Бренды по названию

Популярные бренды

Siemens FDCIO422, Руководство по установке

Результаты поиска

Содержание FDCIO422

Отзывы:

Похожие инструкции для FDCIO422

Бренды по названию

Популярные бренды