Siemens FDA221 Скачать руководство пользователя страница 20

Страница: 20 / 114

Structure and function
Overview

20
Building Technologies

A6V10334410_h_en_--

Fire Safety

2015-09-29

Properties



Patented technology



Can be used with Siemens FDnet/C-NET loop (with optional FDCC221S

installed)



Extended optical detection thanks to dual wavelengths (blue and infrared)



Configuration via USB or FDCC221S (option)



'Out-of-the-box' installation and commissioning



Early detection of a wider spectrum of particle sizes in the air



Software '

FXS2055

ASD Asyst Tool' and pipe configuration supported



Programmable alarm thresholds



Unique dust-resistant detection chamber



Intuitive front indicator for airflow and smoke value



Normalization of the smoke value



Normalization of the airflow



Access to service functions



Different event protocols



Offline/online configuration supported



FDA241, monitoring area of up to 800 m²



FDA221, monitoring area of up to 500 m²



4…20 mA output



Cleaning function (with FDA241 only)



Firmware can be updated locally

3.1.1

Details for ordering

Type

Order no.

Designation

FDA241

S54333-F17-A1

Aspirating smoke detector (8H)

FDA221

S54333-F15-A1

Aspirating smoke detector (5S)

Содержание FDA221



















































































































Результаты поиска

Содержание FDA221

Отзывы:

Похожие инструкции для FDA221

Бренды по названию

Популярные бренды

Siemens FDA221, Техническое руководство

Результаты поиска

Содержание FDA221

Отзывы:

Похожие инструкции для FDA221

Бренды по названию

Популярные бренды