Imp
ort
Ap
plia
nce
s.c
om
THE EASIEST WAY TO SELF-IMPORT APPLIANCES DIRECT FROM EUROPE.
Hood connection
en
33
Notes
■
Make sure you follow the safety instructions in the
instruction manual for your extractor hood and that
these are also observed when operating the
appliance via the hood controls on the
hob.
~
"Important safety information" on page 5
■
Using the controls on the extractor hood always
takes priority. It is not possible to use the hood
controls on the hob during this time.
■
In networked standby mode, your appliance requires
max. 2 W.
Setting up
To set up the connection between the hob and the
extractor hood, the hob must be switched on.
Connecting directly
Make sure that the extractor hood is switched off.
For more information refer to the section entitled
"Connect hob" in the instruction manual for your
extractor hood.
Note:
If you connect your hob directly to the extractor
hood, it cannot be connected to the home network as
well and you will not be able to use Home Connect any
longer.
1.
Touch the
0
symbol for 4 seconds.
Product information will be displayed.
2.
Touch the
0
symbol repeatedly until the
™‚‡
setting appears.
‹
lights up on the cooking position display.
3.
Set the
‚
value on the control panel.
‚
lights up on the cooking position display.
4.
Start connection to the extractor hood within the next
2 minutes.
The hob is connected to the extractor hood when the
„
value appears on the cooking position display. The
symbols for the hood controls on the hob are displayed
on the hob's control panel.
Connecting via your home network
You require a router that has WPS functionality.
You require access to your router.If you do not have
this, follow the steps for "Direct connection".
First of all make sure that the extractor hood is in the
home network.
1.
Touch the
0
symbol for 4 seconds.
Product information will be displayed.
2.
Touch the
0
symbol repeatedly until the
™‚‡
setting appears.
‹
lights up on the cooking position display.
3.
Set the
‚
value on the control panel.
‚
will flash on the hotplate display.
4.
Press the WPS button on the router within the next
2 minutes.
The hob is connected to the home network and the
ƒ
value appears in the cooking position display.
5.
Connect to the extractor hood.
The hob is connected to the extractor hood when the
„
value appears on the cooking position display. The
symbols for the hood controls on the hob are displayed
on the hob's control panel.
Note:
The connection can only be established when
both appliances are connected to your home network
and are engaged in connection. If the connection
process has already timed out for one of the two
appliances, try to connect again (basic settings,
™‚‡
setting).
Resetting connection
You can reset the connections saved for your home
network and extractor hood at any time.
1.
Touch the
0
symbol for 4 seconds.
Product information will be displayed.
2.
Touch the
0
symbol repeatedly until the
™‚‡
setting appears.
3.
Set the
‹
value on the control panel.
Control the hood via the hob
In the basic settings of your hob you can adjust the
behaviour of your extractor hood depending on the
switch-on/off of the hob or individual cooking zones.
~
"Hood control settings" on page 34
You can select other settings using the control panel.
Setting the fan
Switching on
Touch the
I
symbol.
Setting fan level
Select the fan level.
You can choose between the levels 1, 2 and 3. To
select the intensive levels, touch buttons 4 or 5, or
touch the
&
button repeatedly until the required intensive
level is set.
Switching off
Select fan level 0.
Setting automatic mode
Switching on
Touch the
I
symbol until the
‘
symbol appears on the
control panel.
The fan starts up automatically when steam is
produced.
Switching off
Touch the
I
symbol until the
‘
symbol goes out, or
select another fan level.
Setting the hood lighting
You can switch the hood light on and off via the hob's
control panel.
Touch the
=
symbol.