manualshive.com logo in svg

Siemens ERTEC 200P, Руководство пользователя

Siemens ERTEC 200P - это передовой сетевой коммутатор с поддержкой множества функций. Здесь вы можете бесплатно скачать руководство по эксплуатации для этого устройства. Посетите наш сайт manualshive.com, чтобы получить доступ к руководству в формате PDF.

Поделиться
Скачать
background image

 
 

 

Copyright © Siemens AG 2016. All rights reserved 

187 

ERTEC 200P-2 Manual 

Technical data subject to change 

 

Version  1.0 

 

XHIF_CPU_WIDTH(1) is fixed at "0" as an external host with an 8-bit data interface is not 
supported. 

 

Description of configuration pins 

XHIF_POL_RDY =  0: The XHIF module signals to the host that access with XHIF_XRDY 
= 0   

 

 

    is complete (ready). 

1: The XHIF module signals to the host that access with XHIF_XRDY = 1  

 

    

is complete (ready). 
XHIF_ACC_MODE =  

0: Separate read/write lines are provided 

                                 

1: A combined read/write signal is used. 

XHIF_CPU_WIDTH 00:   16-bit data bus of the external host 
 

 

 

01:   32-bit data bus 

 

 

 

10:   8-bit data bus 

                                       

11:   Not permitted 

The configuration signals are synchronized with the XHIF clock. 

 

2.3.6.2.4 Application Information 

The XHIF configurations (16/32-bit data width, ready polarity and read/write line) for the 
XHIF-IP are set with a PowerOn reset over ConfigPins 5...3. Subsequent changes can be 
made to these configurations by the ARM926EJ-S in the 

XHIF_CONTROL 

HostIF regis-

ter over the APB interface. 

XHIF_CONTROL

 should not be changed by the external host. According to the XHIF-IP 

specifications, the external host must not address the configuration registers over the 
APB interface (AHB2APB bridge). ConfigPins 6..0 may 

only

 be set with a PowerOn re-

set.  
The external host can only address the internal XHIF-IP page registers (offset, range and 
buffer mode) and XHIF_VERSION over the register chip select XHIF_XCS_R. Only the 
lowest-value address bits are considered for register selection (address   0x40h are 
invalid according to the XHIF-IP spec).   
Only halfword write/read access to the registers is permitted with a configured data width 
of 16 bits, and only word write/read access with a configured data width of 32 bits. Ac-
cording to the XHIF-IP spec, byte-specific access is not permitted. 
When the memory chip select XHIF_XCS_M is active, write/read access is forwarded 
straight to the HOSTIF AHB master interface and all aligned access types, byte, halfword 
and word, are permitted.  
If you configure a 32-bit data width, the XHIF_ADR(1) pin must be clamped to '0' for the 
ERTEC 200P (XHIF_ADR(0) internal static setting '0') so that there are always word 
addresses internally in the XHIF-IP. 

 

If a data width of 16 bits is configured, the XHIF_ADR(1) pin is required for halfword ad-
dressing and is driven by the external host. 
Initialization procedure for XHIF-IP after reset according to IP spec: 
- Power on reset cleared 
- XHIF configuration with ConfigPins 5...3, thereafter only the ARM926EJ-S can change  
configuration     
  (access by the external host not yet permitted) 
- Page setting by ARM926EJ-S: access over the APB to the relevant registers 
  or page setting by host: access over the XHIF_XCS_R chip select to the relevant 
  registers 

Содержание ERTEC 200P






















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ERTEC 200P

Valve Concepts 3200 Installation, Operation And Maintenance Manual preview
3200
Бренд: Valve Concepts Страницы: 15
ZKTeco SC800 User Manual preview
SC800
Бренд: ZKTeco Страницы: 123
Sole Diesel SVT 10 Operator'S Manual preview
SVT 10
Бренд: Sole Diesel Страницы: 8
Gardner Denver AirSmart G2 Installation Manual preview
AirSmart G2
Бренд: Gardner Denver Страницы: 22
B&G NMEA 2000 Installation Manual preview
NMEA 2000
Бренд: B&G Страницы: 2
Lakeshore 332 User Manual preview
332
Бренд: Lakeshore Страницы: 186
Vaillant VRC 470 Installation Instructions Manual preview
VRC 470
Бренд: Vaillant Страницы: 52
Vaillant VSMART User Manual preview
VSMART
Бренд: Vaillant Страницы: 11
HEIDENHAIN ND 1300 Operating Instructions Manual preview
ND 1300
Бренд: HEIDENHAIN Страницы: 257
K+R Performance Engineering PRO-CUBE Installation And Operating Manual preview
PRO-CUBE
Бренд: K+R Performance Engineering Страницы: 12
CP Electronics AR-SG-4SM-W Product Manual preview
AR-SG-4SM-W
Бренд: CP Electronics Страницы: 12
Oomlout ARDX Experimenter'S Manual preview
ARDX
Бренд: Oomlout Страницы: 32
Wavelength Electronics LDTC2/2E Datasheet And Operating Manual preview
LDTC2/2E
Бренд: Wavelength Electronics Страницы: 25
ABNOX AXTR Series Operating Manual preview
AXTR Series
Бренд: ABNOX Страницы: 84
Halma Alicat Scientific MC Quick Start Manual preview
Alicat Scientific MC
Бренд: Halma Страницы: 2
Casambi CBU-PWM4-4 Manual preview
CBU-PWM4-4
Бренд: Casambi Страницы: 4
Universal Remote Control total control MRX-10 Owner'S Manual preview
total control MRX-10
Бренд: Universal Remote Control Страницы: 16
SainSmart 101-40-173 Assembly preview
101-40-173
Бренд: SainSmart Страницы: 17

Бренды по названию

Популярные бренды

Загрузить еще бренды