Siemens ED FQ2 Series Скачать руководство пользователя

Страница: 33 / 40

Trouble shooting

Trouble shooting

Trouble shooting

Usually, faults are small matters that are easy to

eliminate. Please read the information in the table

before calling the after-sales service.

Notes

■

“

appears on the display, press and hold the

button for the relevant cooking zone in order to read

the fault code.

■

If the fault code is not listed in the table, disconnect

the hob from the mains power supply and wait

30 seconds before reconnecting it. If this code is

displayed again, contact the technical after-sales

service and specify which fault code has appeared.

■

If a fault occurs, the appliance will not switch to

standby mode.

Display

Possible cause

Solution

None

The power supply has been disconnected.

Use other electrical appliances to check whether a short circuit

has occurred in the power supply.

The appliance has not been connected as shown

in the circuit diagram.

Ensure that the appliance has been connected as shown in the

circuit diagram.

Electronics fault.

If you are unable to rectify the fault, inform the technical after-

sales service.

The displays flash.

The control panel is damp or there is something

on it.

Dry the control panel or remove the object.

The

display flashes in the

cooking zone displays.

A fault has occurred in the electronics.

To acknowledge the fault, briefly cover the control panel with

your hand.

”

The active carbon filter is saturated or the satura-

tion indicator lights up even though the filter has

been cleaned or replaced.

Change the filter and reset the filter saturation indicator. You can

find additional information about this in section

"Cleaning"

”ƒ

The electronics have overheated and have

switched off the affected cooking zone.

Wait until the electronics have cooled down sufficiently. Then

touch any symbol on the hob.

”…

The electronics have overheated and all of the

cooking zones have been switched off.

”†

+ power level and audible

signal

There is hot cookware near the control panel.

There is a risk that the electronics will overheat.

Remove the cookware that is causing the problem. The fault dis-

play goes out shortly afterwards. You can continue cooking.

”†

and audible signal

There is hot cookware near the control panel.

The cooking zone has been switched off to pro-

tect the electronics.

Remove the cookware that is causing the problem. Wait a few

seconds. Touch any touch control. When the fault indicator goes

out, you can continue cooking.

”‚

”‡

The cooking zone has overheated and has been

switched off to protect the work surface.

Wait until the electronics have cooled down sufficiently. Then

switch the cooking zone on again.

”‰

The cooking zone has been operating continu-

ously for an extended period.

The automatic safety cut-out function has been activated. You can

find additional information about this in section .

“Š‹‹‹
“Š‹‚‹

The operating voltage is incorrect and outside of

the normal operating range.

Contact your electricity supplier.

—…‹‹

The hob is not connected correctly.

Disconnect the hob from the mains. Ensure that the hob has been

connected as shown in the circuit diagram.

Do not place hot cookware on the control panel.

Содержание ED FQ2 Series









































Результаты поиска

Содержание ED FQ2 Series

Отзывы:

Похожие инструкции для ED FQ2 Series

Бренды по названию

Популярные бренды

Siemens ED FQ2 Series, Инструкция по эксплуатации

Результаты поиска

Содержание ED FQ2 Series

Отзывы:

Похожие инструкции для ED FQ2 Series

Бренды по названию

Популярные бренды