Siemens DF8000 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 46

Siemens DF8000 Скачать руководство пользователя страница 32

28

Building Technologies

048_DMS_DF8000_ICC_MP4.15_A6V10081388_c_en.doc

Fire Safety & Security Products

06.2008

7.3

DF8045/46 front panel

Three dip-switches, located on the front panel of the DF8045/46 (refer to Fig. 24),
are used to set the module’s I

2

C address. Although there are 8 possible selections,

from 0 to 7, the valid I

2

C address can range from 0 to 2 (single unit) or 0 to 5 (dou-

ble unit). Refer to Annex B on page 36 for a complete list of the valid DF8000 con-
figurations.

Furthermore, 8 LEDs on the same front panel indicate the physical state of the in-
dividual inputs: the green LED is on when the input is in normal operation, the red
LED is on when an alarm condition is detected, in case of tamper (cable short or
open) both LEDs are on. These devices can be disabled from the CPU module to
reduce power requirements (see 4.1 and 10.4).

Fig. 24 DF8045/46 Front panel and external connections 1-8

Module
Address

Switch 1

Switch 2

Switch 3

Notes

0

Off

↓

Off

↓

Off

↓

1

st

module

1

On

↑

Off

↓

Off

↓

2

nd

module

2

Off

↓

On

↑

Off

↓

3

rd

module

3

On

↑

On

↑

Off

↓

4

th

module

4

Off

↓

Off

↓

On

↑

5

th

module

5

On

↑

Off

↓

On

↑

6

th

module

Tab.16. DF8045/46 Module Address settings

EMI filters on the DF8045/46 are dimensioned for the documented power supply
ratings.

Max input voltage

33 VDC

Max forward current

7 mA at 33 VDC

Tab.17. DF8045/46 max. ratings

7.4

DF8045/46 module mechanical dimensions

Width 45

mm

Height 75

mm

Depth 48

mm

Tab.18. DF8045/46 mechanical dimensions

I²C connector to
I/O modules

LEDs reporting status of inputs:

–

Left LEDs (Green): Normal

–

Right LEDs (Red): Alarm

–

Both / None: Tamper

Dip-switches for
address selection (1...6)

I²C connector to I/O
modules or CPU module

9

10

11

12

13

14

15

16

8

7

6

5

4

3

2

1

1

DF8045

1

2

3

4

ALARM

NORMAL

TAMPER

«
...
30
31
32
33
34
...
»

Содержание DF8000















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды